logs

Hi peeps, putting these logs on for a friend (matt s) as requested, just would like some opinions really mainly on the cf's as these are before. and after using lemmiwinks with putting timing +3 deg forward but the cfs went fairly high..... before timing Group A: 115 Group B: 002...

Ran the car the other week at RS Tuning RR day and it only made 186bhp. Now I know there is the old dyno lottery but I was first on at 10am and last time on the same rollers I made 173bhp with out the APR stage 1 and CAT back system. I was expecting around 205-210bhp maybe more if I was lucky...

I finally got round too doing some logs on the Leon Cupra R as i bought the car and the previous owner mentioned it had been remapped, but i wanted to make sure, So i bought a Revo Sps 1 to switch the map and off, and decided to do some logs to see if could tell the difference on Meas Bloc...

Hi all, I fitted an FMIC recently to my Octavia Vrs with the AUQ engine (same as the cupra). I had this before fitting but the actual does not meet up to the requested boost. The N75 is in no way maxed out as the graphs show, so why doesn't the N75 compensate for the difference? Any advice...

Hi guys I briefly brought this problem up a week or so back but I wanted to see if we had rectified it but no such luck. I'll go from the top as the full story i hope will help. Basically prior to getting my car mapped, it would 80% of the time boost and hold 11/12psi but i had terrible...

New to vag com so bear with me.Can someone take a look at thes logs and tell me if all is ok.Settings used were B6 T5 using tesco 99.I understand the the timing could be advanced further having shown no cf in group 020 but was unsure about group 115.I believe my peak boost to be 19psi which...

I've done a few logs the other day to check for my ongoing problem. I'm getting the following error: 17521 - Oxygen (Lambda) Sensor: B1 S1: Internal Resistance too High P1113 - 35-10 - - - Intermittent I've changed the lambda sensor with a new one (NTK/NGK) and I'm still getting...

Hi, Im not to good with the logging side of things so was just wondering if there is any logs i can do to check my car as im running way to less bhp and torque so could do with checking thins to see if they are up to scratch... or it may be my map... time will tell.. thanks

I need to do some boost logs, to see if my cars been remapped, ive owned my R for a month now, and when i bought it, it had instructions in the manuals for a Revo SPS1 Just need to know what psi its boosting at. Thanks in advance Craig.

Hi, Did some logging yesterday, can someone have a look and see if it's possible to run more timing? Thanks :) Group A: '020 Group B: '011 Group C: '002 Idle Stabilization Idle Stabilization Idle Stabilization Idle Stabilization RPM Temperature Temperature Ign. Timing...

aup lads firstly wana say thanks 2 chriscurzon and danny lad for logging my car and adding some timing via lemmiwinks made a big difference thanks agen both top lads they are gonna post my logs up shortly let us no what ya think thanks

Hi All, My car has been having boost problems whilst accerating. Basically the boost cuts in and out. I've done some block measuring in 3rd gear, could anyone shed any light on what they think the problem may be? Saturday 28 February 2009 21:41:09 06A 906 032 HN 1.8L R4/5VT...

Hi Guys; I have just vagcommed my LCR after having some limp-mode issues every once in a while. The fault codes are: 16486 P0102 Mass or Volume Air Flow Circ Low Input 17863 P1455 Exhaust gas temperature sensor 1 range/performance 17963 P1555 Charge Pressure Upper Limit exceeded 18010...

Is this possible? I have a 2 port MBC in parallel with my N75 to stop boost spikes. Occasionally my boost is limiting to 6psi; but after a good stint of full throttle will shoot back up to normal levels ~24psi peak. I am thinking either my MBC is sticking keeping the wastegate open; or i'm going...

I wonder if someone can help me/make any sense of this. To start with the whole story: In september I took my car off the road for 2 and 1/2 months, while I took off my manifold, KO3S, TIP, Full turbo back exhaust system, while I sourced GT28 Parts. While it was off the road, I have taken...

Right guys got my new maf fittted today along with my cai from the bay, but to no avail it still boosts in 1st, go into second get up the revs and bang it feels like someone has just stamped on the brake pedal, into 3rd and it just revs all the wayround with no boost? Any ideas? With...

Done Some logs tonight with curzon to make sure its all heathy and if theres any room for improvment.. My mods Are: Custom jabbasport map 4 bar Atp Manifold 3'' downpipe and De-cat 2.5 cat milltek system forge tip Fmic Uprated Fmic pipe work (68mm) k03s 320bhp jetex filter 007p...

Did some logs tonight so thought i would post them up see what you think. My WG duty is still 95.3 most of the time but has always been like this even after changing intercooler so not sure if its the way car is mapped as its always requesting max boost high up revs? See what you think...

It's been a long time coming.... I’ve been thinking of posting something in here for a while. I bought this (my first SEAT) back in 2004 with less than 8000 miles on it. It was totally standard and looked something like this It wasn’t until joining SCN early last year that I (like many...

002 and 020 6.77 0 0 0 0 7.17 2240 36.8 5.33 21.58 7.57 0 0 0 0 7.97 2320 113.5 12.71 55.75 8.37 0 0 0 0 8.77 2520 178.2 22.14 95.31 9.17 3 3 3 0 9.57 2840 191.7 25.83 119.47 9.97 3 3 3 3 10.37 3160 191.7 25.42 121.22 10.77 3 2.3 2.3 3 11.17 3440 191.7 25.83 147.94 11.58 2.3 2.3 1.5 3...