what have you done to your car today ?

[Thai-wronghorse]

Loads of used starter motors in stock here mate.

Sent from my SM-S906B using Tapatalk

 

[Manic172]

Highly recommend the Thai breakers

 

[tracktoy]

Will more than likely get it mapped on v power.
But also get a secondy map for the BP 103. It's more available in Europe but is found at some BP near race tracks

Have you ever tried using Unleaded Fuel Accelerator to change the octane rating and if so are they any good.

 

[Nam-uk]

Loads of used starter motors in stock here mate.

Sent from my SM-S906B using Tapatalk

Any High level brake lights?

 

[iammooks]

Loads of used starter motors in stock here mate.

Sent from my SM-S906B using Tapatalk

I need to put you on speed dial...

Will drop you a DM...


Sent from my iPhone using Tapatalk

 

[Manic172]

I used to use it in the saxo race car, main used silkolene pro-boost. that had stupidly high compression. The higher the octain level the higher your compression needs to be. When all sorted I will figure out the cr and try adding a bit of obtain booster to the v power
I have even run a very low ratio of 2 stroke fully synthetic oil in the fuel befor to aid lubrication. This was because the engine used to rev to 8.5k, and in my thoughts any little helps.
A small ratio cos if it don't burn off it can then build up on the piston crown and cause hot spots that can melt threw the piston and then that's bye bye engine lol.

 

[MoToJoJo]

I'd forgotten how much I hate rear brake lines. Not quite exhaust level hatred, but definitely not my favourite thing to work on

 

[ExiledWeegie]

did the timing belt and waterpump yesterday with a gates kit upon starting it up and letting it get upto temp i noticed a drumming sound coming from the timing cover area so stopped the engine and left it until today. ive taken off the crank pulley and timing covers and ran the engine and seems to be coming from either the waterpump or hydraulic tensioner so ive ordered a febi kit to come tomorrow and ill do the job again and send this gates kit back as faulty. nightmare.

today i also fitted a boost gauge and installed the stalk for cruise control from the kufatec kit, will need to wire all that up after ive done this timing belt job

 

[MoToJoJo]

I've never been a fitment kinda person... but this ain't bad

Almost done, just got to finish tracing any fluid leaks then it's back on its wheels. If I get time, I might even splice together the wheel speed sensor wiring

 

[MoToJoJo]

Don't think my car likes either its new wheel speed sensors or the wiring I did was off. Either way, I get to drive with TCS off until I get it sorted

 

[Dazzalcr]

I'd forgotten how much I hate rear brake lines. Not quite exhaust level hatred, but definitely not my favourite thing to work on

Yeah with you on that when we did mine with extended lines absolute nightmare just no room to get tools there to do job properly fronts we're a breeze in comparison, nice fitment on tyres I'd say we have the same nice flush like to the arch, font like when ppl have them pokein out.

 

[Dazzalcr]

Well only having replaced the fuels lines to the fuel rail about a yearish ago had to do it again, when I started the motor other day I thought that's running really rich then saw rainbow effect in the water on ground grrrr, so replaced them and the difference in quality from fuel lines off ebay to to the car shop was massive ebay looked very cheap and poor against new 1s, so just maybe my dad's acceleration foot was not as heavy as 1st thought .

 

[Manic172]

Well only having replaced the fuels lines to the fuel rail about a yearish ago had to do it again, when I started the motor other day I thought that's running really rich then saw rainbow effect in the water on ground grrrr, so replaced them and the difference in quality from fuel lines off ebay to to the car shop was massive ebay looked very cheap and poor against new 1s, so just maybe my dad's acceleration foot was not as heavy as 1st thought .

Can still blame him for the excessive fuel consumption

 

[Manic172]

I need a massive favour. I am not bale to get to the workshop to play cars but I need to order some thing..
Is some one able to measure the length of the front and rear door seals.
I am going to order some new ones . But slightly different .

Am going for some thing like this. So it seals the door but I don't need the flap but that goes over the plastic trims
Also I need the rough size of the rounded bit so I can get the right size

just so I can compare to the sizes here.
It would be amazing if some one could. As I not spent any thing on the car today.... I have bought grass seed and grass fertiliser... but nothing for the money pit. Hahhaa

 

[iammooks]

I've never been a fitment kinda person... but this ain't bad

View attachment 44095 View attachment 44096

Almost done, just got to finish tracing any fluid leaks then it's back on its wheels. If I get time, I might even splice together the wheel speed sensor wiring

Could probably get good money for that...


Sent from my iPhone using Tapatalk

 

[iammooks]

Either way, I get to drive with TCS off until I get it sorted

Oh no.


Sent from my iPhone using Tapatalk

 

[Nam-uk]

did the timing belt and waterpump yesterday with a gates kit upon starting it up and letting it get upto temp i noticed a drumming sound coming from the timing cover area so stopped the engine and left it until today. ive taken off the crank pulley and timing covers and ran the engine and seems to be coming from either the waterpump or hydraulic tensioner so ive ordered a febi kit to come tomorrow and ill do the job again and send this gates kit back as faulty. nightmare.

today i also fitted a boost gauge and installed the stalk for cruise control from the kufatec kit, will need to wire all that up after ive done this timing belt job View attachment 44090 View attachment 44091 View attachment 44092 View attachment 44093 View attachment 44094

Check the Alternator Pulley as that can make odd noises the service on them is like 40-70k its overlooked

 

[ExiledWeegie]

I took the aux belt off and ran the engine to rule all the pulleys out and its deffo coming from the waterpump by the looks of it, theres a slight wobble to it when the engines running, rain has stopped play though so will need to get it all changed tomorrow.

 

[MoToJoJo]

Could probably get good money for that...


Sent from my iPhone using Tapatalk

The Audi hub cap type thing?

 

[iammooks]

The Audi hub cap type thing?

Is it the FR one? There's probably thousands of those that have been destroyed by KwikFits across the land.


Sent from my iPhone using Tapatalk