Does your mrs know you use the oven for the car..
what have you done to your car today ?
- Thread starter seatcupramad23
- Start date
Manic172
https://m.facebook.com/ManicMotorsport1
. Luckily this was at work.. but if I was at home.. I would wait till she went shopping
Manic172
https://m.facebook.com/ManicMotorsport1
I swear, any job you think is going to be straight forward, even down to loosening a few simple screws, it never f ing is!Went to replace brakes - discs & pads - only to find the passenger rear caliper is totally seized
Sent from my iPhone using Tapatalk
I replaced my antenna a few weeks back, easy enough job. That was until removing the plastic. One screw fell out, no thread, the other was stuck in spinning.
I got around that, but then replacing all the trim/plastic after I finished was an absolute nightmare. For the life of me, I still can't get it to sit tight like it was before. It was any icy day, I was sat in the boot & the swear words poured out of my mouth.
Good luck m8, I feel your pain.
Manic172
https://m.facebook.com/ManicMotorsport1
Right. If you lot can keep a secret. I have some photos of some thing that is being made for me... but these are NOT ment be be public. So if you all promis not to share or show other forums, the book of face etc.. I will post them in my build page.. but you have to promise 
Right. If you lot can keep a secret. I have some photos of some thing that is being made for me... but these are NOT ment be be public. So if you all promis not to share or show other forums, the book of face etc.. I will post them in my build page.. but you have to promise
Promise not to tell a sole about………….wait what was I going to tell
Sent from my iPhone using Tapatalk
Not a peep from meRight. If you lot can keep a secret. I have some photos of some thing that is being made for me... but these are NOT ment be be public. So if you all promis not to share or show other forums, the book of face etc.. I will post them in my build page.. but you have to promise
. You won't even find me on dem sites...unless it's OF? 
Manic172
https://m.facebook.com/ManicMotorsport1
I am to old to go on them hahahahNot a peep from me
Not my cup of tea.
Passed. Just need some new tyres apparently.
Best thing about it is that it hasn't failed because of anything I've done.
When the headlight bolt snapped I didn't know if I'd bent the panel drilling it out, that and the fact the re-tapped hole was slightly off centre. How on earth do you align headlamps anyway? Turns out I didn't have to worry - about that, or the fact my front number plate is a post-Brexit UK plate and the rear one an EU GB plate. Should be an instant MoT fail that - horrifying lack of attention to detail.
Sent from my iPhone using Tapatalk
With you on the number plates there mate.
Ive been running my daily motor for 9 months with a blue EU one on the back and a plain one on the front. Don’t know how I’ve slept at night. Worse thing is I’ve had two brand new matching ones in the shed since a week after I got the car and I just haven’t put them on yet.
One of my greatest days last year was applying a brand new numberplate to a newly painted rear bumper!
Manic172
https://m.facebook.com/ManicMotorsport1
Just a question.. does any one know what thread, pitch and length the sump bolts are for a 1.8t
I have read they are m7 x 1 but no length. Is any one able to confirm these details
I have read they are m7 x 1 but no length. Is any one able to confirm these details
Replaced both rear calipers, discs & pads, pressure bled system but still have a soft brake pedal 
Will have to look at bleeding master cylinder 2moro!!
Sent from my iPhone using Tapatalk
Will have to look at bleeding master cylinder 2moro!!
Sent from my iPhone using Tapatalk
Similar threads
