• Guest would you be interested in CUPRA or SEAT valve caps? let us know in the poll

  • Welcome to our new sponsor Lecatona, a brand dedicated to enhancing performance for VAG group sports cars, including SEAT, Audi, Volkswagen and Škoda. Specializing in High Pressure Fuel Pump (HPFP) upgrades.

what did you and your mk3 leon do today

rob280

Active Member
Oct 27, 2019
135
53
Had a dent removed by autodentz Plymouth. Well happy with the result.

Sent from my SM-A405FN using Tapatalk
 

billman

Active Member
Dec 20, 2009
120
19
The RacingLine dogbone mount states it’s not suitable for use for aluminium subframes - I’m assuming because of how harsh it is?

I’ve not managed to test the car properly yet - been on a short drive and car feels a bit tighter round bends at speed. Nothing else to report just yet.

I took these photos during the install, not sure if it helps:

ea8699638354022d2c4bb56e8fb9c85c.jpg
b194199103de1baba88aa8e8323e6718.jpg
a8a6ffe6a0a04047f80903603a70c861.jpg
95635d8451740508aed678c2bc393f53.jpg
949d253a042e082ea6faaeeb53b4171d.jpg
4fb68eb79b75654bdb7536d296fd3ec5.jpg
47c3ce34838b0083b0ebb4e3aee07320.jpg
42d96b5dbc8d6195ce41730c66f26023.jpg
c93788127fe0f97ecd55ab9975bb3695.jpg



Sent from my iPhone using Tapatalk Pro

Thanks for the photos. You placed it over the carpet, you didn't cut it? I didn't know that about the racingline mount. As far as the plastic trimming I guess you could have done it a bit better as you said! :bleh: :coolthumb I don't know how easy it would be to measure it and cut a hole with a hole cutter or a step drill for the tube and then cut the plastic in two horizontal lines and place it again. I don't know if you can understand what I am saying. I don't know if its possible to do it and of course everything is always easier behind a keyboard. If I buy one I will try it though. The shipping cost is killing me and is holding me back. 85£ for shipping is way too much for me.
 
  • Like
Reactions: paddy6789

paddy6789

Moderator
Staff member
Moderator
Aug 31, 2016
1,627
1,080
Preston, Lancs
Thanks for the photos. You placed it over the carpet, you didn't cut it? I didn't know that about the racingline mount. As far as the plastic trimming I guess you could have done it a bit better as you said! :bleh: :coolthumb I don't know how easy it would be to measure it and cut a hole with a hole cutter or a step drill for the tube and then cut the plastic in two horizontal lines and place it again. I don't know if you can understand what I am saying. I don't know if its possible to do it and of course everything is always easier behind a keyboard. If I buy one I will try it though. The shipping cost is killing me and is holding me back. 85£ for shipping is way too much for me.

Well I’m ordering new bits of plastic trim anyway, so I can use the ones I’ve got as a template to tidy it up. I used a dremel to essentially cut and sand the plastic into shape. Then got a bit tired of the back and forth so gambled and took too much off :(

Once I drilled the holes and put the nuts in the holes, I placed the carpet back over everything and then used a screw driver to pierce a hole for the screw. I then used a knife to cut a tiny hole to allow the screw to pass through to the nut. (Hopefully that makes sense)


Sent from my iPhone using Tapatalk Pro
 
  • Like
Reactions: billman

billman

Active Member
Dec 20, 2009
120
19
Yeah I understood how you marked the carpet for the hole. Regarding the plastic trim I don't know if a Dewalt laser would do the trick for marking the hole of where the tube goes through it. Masking tape on the carpet outside of the area that the plastic clips on with strut also on obviously and then marking with the laser. Then strut off plastic on and you find the center of the hole for the tube on the plastic trim. Drilling, cutting of the plastic etc.That's how I would do it.
 

who.am.i

Leon FR
Jan 23, 2016
392
30
EU
Finally fitted new summer tyres. Huge diference



Poslano z mojega SM-G390F z uporabo Tapatalk
605c95c028a61d6cbb2c7951f1cbfa22.jpg
 
Last edited:

Rooster

Active Member
Oct 27, 2018
1,188
326
Yorkshire
Took the opportunity of the lockdown to replace the timing belt and serpentine belt kits, not the worst i have ever done but not the easiest either. Timing belt was coming up six years old but only done 37k, it was slack and was well polished and only showed minor cracking to the tooth roots and the backing surface, so didn't look like it would have given up any time soon, but you can't see the internal structure of the belt so i played it safe. Locking tools are required and make the job a lot easier and safer. Good practice though as i will do the Golf next year.
 
  • Like
Reactions: Hag and Walone

H3I53

Active Member
Nov 27, 2019
5
10
denmark
IMG_0041.jpg
Gave it a proper wash, vacuumed the inside, gave the leather parts some leather soap.
Changed back to summer wheels
Would have removed the number plate frames, but the plate itself is screwed to the frame, which then again is screwed to the car.
So holes dont match if i remove the frame :censored:
 
  • Like
Reactions: Hag

KXL

KXL
Dec 15, 2016
1,579
195
London, UK
Went to check the car, been sat there for weeks, went to push it a bit to avoid flatspotting tyres....found a large windscreen crack first (probably large ish branch fell on it), called to find out who's my insurer's approved glass repairer. Found out that I'm not an indicated key worker, so they won't be called out to replace the glass with no indication when they can eventually, so car will be sat there another month or so, forgot to push the car!
 
  • Like
Reactions: Kirky

Rockbox

Active Member
Apr 6, 2018
162
52
Reset service and inspection message as I cannot get it serviced at the moment even though I'm a key worker.
 

Alorjosh

Active Member
Apr 23, 2019
159
70
East Anglia
Seen something a while ago. Behind the front plate, eazimods / others do a black wrap pre cut for this.

Anyone got a link


Sent from my iPhone using Tapatalk
 

Fortis

Active Member
Jul 11, 2019
40
3
Seen something a while ago. Behind the front plate, eazimods / others do a black wrap pre cut for this.

Anyone got a link


Sent from my iPhone using Tapatalk
Don’t think they’re a very good fit tbh, easier to buy some and cut your own shape
 

Hag

Active Member
Sep 15, 2018
399
193
Quick wash.


It'll be up for sale end of this month, time for a Cupra :) pm if anyone's looking for a nice FR
710196589c2d0efeb7adc3914f269664.jpg
60f88ba589dcefc453d4260d9c996e86.jpg


Sent from my CLT-L09 using Tapatalk

Is that the Maxton Rear Diffuser/ Valance


Sent from my iPhone using Tapatalk
 
Lecatona HPFP (High-pressure Fuel Pump Upgrades)