what have you done to your car today ?

[bruceR]

Yes, the pressed steel wishbones are like that


Sent from my iPhone using Tapatalk

 

[Connor H]

Yes, the pressed steel wishbones are like that


Sent from my iPhone using Tapatalk

Thank f*ck lol. I had a mild internal panic when i saw them off the car.

 

[Thai-wronghorse]

Yep, only the cast Cupra R arms are handed.

Sent from my SM-G960F using Tapatalk

 

[lightup]

Swapped fender to fix damage from some unknown hit an run and fixed the topmountbearings. (Fitted by the garage a few months ago. One side was fingerloose allready and the other side looked like the last picture. )

Verstuurd vanaf mijn SM-G960F met Tapatalk

 

[Yellow fr]

I have fit a arm rest and a fr metal plate to the foot rest will get pictures later


Sent from my iPhone using Tapatalk

 

[Manic172]

I went a spent too much money again .... see build thread for details lol

 

[seatturbopower]

Car failed its MoT on emissions and tyres today. Hopefully the emissions I'll have in hand by just going for a long drive over the weekend with some Millers in the car, but any thoughts on tyres?

I've got Avon ZV7s on there at the moment, and they've been fine, but started perishing pretty quickly - I live in Brighton and the sea air seems to bugger things up, while I also don't do that many miles anymore, so that probably explains a few things too - average of 2,000 miles a year.

I know everyone will have their own favourite tyre, but thought I'd throw it out there. I loved Pilot Sports, but they're too expensive for the kind of driving I do these days, and when I tried Pirellis they only lasted about 8,000 motorway miles.

How about Bridgestone Potenzas?

..................... emissions????haha if id had taken my car to kwit fit then they would like to know why its off the scale....until thy see its got no catalytic converter as for the tyres I have toyo r 888s there not bad managed a good few track days in them. But once you get more heat into them its then you realise you need semi slicks( full if you have the chance to hold both)

 

[iammooks]

The big job today was taking out the EGR and cleaning it - which actually turned out really well.

The other job, well, the photo will give you an idea. Don't know why I left it so long...

Sent from my iPhone using Tapatalk

 

[Connor H]

Fitted a 70 quid pioneer head unit from Halfords

and just finished fitting an eBay special downpipe to the standard cat back until I get a custom one. To our surprise it went on a treat, 80 quid well spent!

 

[Leon20vt4]

New high flow k03s manifold came in.

Also tested the new 3d printing material, and oh my god... Stronger than ABS!

Sent from my RMX1993 using Tapatalk

 

[Manic172]

I just keep looking at all the shiney bits lol.
I for got to take photos but now stripped all the underseal/stone chip stiff along the will and also all the sealer in the boot. Every little helps for weight saving

 

[Leon20vt4]

Making some good progress in the late night on the Cupra R front grill honeycomb design same honeycomb size as the cupra top sport grill. Still some work to do... To be continued tomorrow!

Sent from my RMX1993 using Tapatalk

 

[iammooks]

Making some good progress in the late night on the Cupra R front grill honeycomb design same honeycomb size as the cupra top sport grill. Still some work to do... To be continued tomorrow!

Sent from my RMX1993 using Tapatalk

Woof...

While I was removing my EGR valve on Saturday, I noticed one of the lines has been resting on the actuator and there's an imprint of it in the hose.

Is this something I should be concerned about? Nothing seems to be happening or not happening as a result of this, but I don't want to cause myself big and expensive problems further down the line that I could stop here and now.

Sent from my iPhone using Tapatalk

 

[Yellow fr]

I would just tie it up out off the way so it’s not rubbing as over time it will rub all the way through and cause a issue


Sent from my iPhone using Tapatalk

 

[bruceR]

Replace it all with 4mm silicone piping


Sent from my iPhone using Tapatalk

 

[iammooks]

Replace it all with 4mm silicone piping


Sent from my iPhone using Tapatalk

I think it needs it - I just had a feel of it and it's really thin where it's worn.

You might not be able to tell from the photo, but where does it go? There's a connector I can take one end off a few inches further up, but it goes down in the other direction and I don't know whether it's something I'll need to get under the car to change.


Sent from my iPhone using Tapatalk

 

[iammooks]

I think it needs it - I just had a feel of it and it's really thin where it's worn.

You might not be able to tell from the photo, but where does it go? There's a connector I can take one end off a few inches further up, but it goes down in the other direction and I don't know whether it's something I'll need to get under the car to change.


Sent from my iPhone using Tapatalk

This might help - it goes behind the air intake pipe and it feels like it reaches a clip of some sort, and then what feels like some braided hose starts.

Sent from my iPhone using Tapatalk

 

[Yellow fr]

Is it the pipe I have marked ?

If it is it’s the servo pipe it should just pull out of the servo


Sent from my iPhone using Tapatalk

 

[Connor H]

Making some good progress in the late night on the Cupra R front grill honeycomb design same honeycomb size as the cupra top sport grill. Still some work to do... To be continued tomorrow!

Sent from my RMX1993 using Tapatalk

I found it strange when i got my Cupra i noticed that the LCR's have a different grill pattern. Whats with that? Im not sure what I prefer, possibly the honeycomb but im biased lol.

While we're on the topic of Grills, does anyone have any recommendations for what to paint the grill plastic with? Mine up close needs a touch up as its got some kind of overspray or something on it.

 

[iammooks]

Is it the pipe I have marked ?

If it is it’s the servo pipe it should just pull out of the servo


Sent from my iPhone using Tapatalk

It's this one - it comes down and disappears round behind the air intake. I can try and get in there tomorrow when it's light and try to take a clearer photo, but it seems to connect to either something braided or some kind of ribbed plastic pipe.

This second photo isn't in focus, but you can see the worn hose at the top and get a bit more of an idea where it leads.

Sent from my iPhone using Tapatalk