What did you and your MK2 do today?

[olitaylor07]

Hahaha, just pulling it out the garage for you mate.

Sent from LG G2 using Tuppytalk

Got lost on the way down didn't i. Damn


Sent from my iPhone using Tapatalk

 

[betty_swollox]

Figures seem a little low for stage 2+

Sent from LG G2 using Tuppytalk

They do seem low, your car made that stage 1 with intake didn't it?

I said that to him before!!!


Should be at least 360 with pump, intake and downpipe

 

[anarchy1515]

All on a private road too eh

did anyone say I broke the speed limit just mearly driving to the conditions but yes there are lots of private roads

 

[Joshkcupra]

I said that to him before!!!


Should be at least 360 with pump, intake and downpipe

They did say there was a problem with the inlet manifold motor, which would lead me to believe it isn't opening/closing properly meaning there is a drop in pressure?

 

[richicupra]

Looking for a good garage in the north west to fit a clutch - any suggestions?

 

[betty_swollox]

Looking for a good garage in the north west to fit a clutch - any suggestions?

Awesome?? Statller??

 

[Dan FR]

They did say there was a problem with the inlet manifold motor, which would lead me to believe it isn't opening/closing properly meaning there is a drop in pressure?

What exhaust are you running? Read of a few cars getting stuck at 330 ish hp with power nose diving at high rpm when on the standard catback or a poor flowing after market system

 

[betty_swollox]

What exhaust are you running? Read of a few cars getting stuck at 330 ish hp with power nose diving at high rpm when on the standard catback or a poor flowing after market system

Wouldn't have happened if he had a BCS system (just kidding lol, but it's true haha)

Think he has downpipe, not sure on intake tho

Really low tho for stage 2+

 

[Joshkcupra]

It's a 3" downpipe with 100cell cat, with blueflame 3" cat back.. Don't think it's the exhaust as I said I think it's the intake manifold motor

 

[richicupra]

Awesome?? Statller??

Cheers, I've got a quote from Awesome. Just seeing where others have had theirs done and where is recommended as well - see what my options are.

Going to uprate the clutch then see about more power

 

[olitaylor07]

So been cleaning the car today ect and I've used tardis and iron x and can't get rid of these little *******. There orange in the flesh.

Sent from my iPhone using Tapatalk

 

[STU3Y]

I use gunk universal degreaser and a brush to agitate. It softens it enough that you can take it off with a fingernail or use the abrasive back of a noodle wash mitt. Sounds a bit funny but I spray it on and dont leave it on too long. Never done any damage to my paint

 

[cupra.al]

might be worth claying over the orange spots.

 

[olitaylor07]

Already clay'd over them. Will have to try what STU3Y says.


Sent from my iPhone using Tapatalk

 

[STU3Y]

Otherwise good old fashioned t cut, or g3 compound applied by hand.

 

[mike0105]

Had a go at cleaning the exhaust with a bit if Tcut. Works quite well, but is bloody hard work. Cleaned the car and sorted the black trim out, car looks ace now!

 

[olitaylor07]

Did my exhaust today aswell. Come up well with abit of elbow grease. Has slight rusting at the tips which it got rid off. Also used autoglym bumper care and all the valance, scuttle panel and pillars came up very well


Sent from my iPhone using Tapatalk

 

[locky]

Just bought a Revo ceramic intake

 

[Jarre]

Already clay'd over them. Will have to try what STU3Y says.


Sent from my iPhone using Tapatalk

Clay harder

 

[olitaylor07]

Mate I was knackered yesterday. Was in my dads garden yesterday digging 3 foot holes for the decking into clay. And my arms where dead yesterday at the end. :-(


Sent from my iPhone using Tapatalk