Going to build a race 1m

Manic172

https://m.facebook.com/ManicMotorsport1
Dec 4, 2018
1,446
1,574
Hemel hempstead
www.seatcupra.net
I have now been making a few fuel line and sort of got the hang of of it. It seams easy but it's fidderly too.
So mark out your pipe and cut with either a grinder or big metal cutters
Put tape areound befor you cut it helps to stop it from slaying out
20250401_200046.jpg
20250401_200105.jpg


I have plastic coated braided hose. So I need to cut that back about 6-8mm
20250401_200257.jpg

The fittings are for teflon hose .
20250401_200158.jpg

Make sure you have the right fittings for the type of hise your using. . The teflon ones have this olive to seal against the tubing
20250401_200208.jpg
so started off take your tape off and slide the nut over the tube . Then open out the steel braiding.
20250401_200321.jpg
then slide the olive on down to the shoulder of it
20250401_200438.jpg
using the special tool to open out the tubing to make sure the fitting slides in is this special tool
20250401_200450.jpg
you can get all differnt ends for different size and fittings then slide the rest of the fitting in to the tube
20250401_200500.jpg
all the way to the end
20250401_200550.jpg
then I bought these ally clamps to not scratch the fittings that fit on to the vice
20250401_200608.jpg

Also these ally adjustable spanners too also so they don't scratch. And then tighten
20250401_200732.jpg
 

Manic172

https://m.facebook.com/ManicMotorsport1
Dec 4, 2018
1,446
1,574
Hemel hempstead
www.seatcupra.net
A big thank you to fuelabs the the 2 low pressure intank pumps
20250402_193343.jpg
an to torques for the 2 pick up pipes that go on to the tank and bulk head connections to suit
20250402_193351.jpg

So remove the old fittings
20250402_193952.jpg
and screw in the new ones
20250402_194035.jpg
the push the pipe on to the barbed end and on to the pump. Do this for both. And secure with the jubilee clips supplied
20250402_195516.jpg

Just need to wire in. I have drilled and fitted a electrical gland for the wire to go threw.
When wired in I will refit the foam insert. And screw the top down..... might have to buy some fancy screws for that..🤔 off to eBay
 
  • Love
Reactions: nd-photo.nl

Manic172

https://m.facebook.com/ManicMotorsport1
Dec 4, 2018
1,446
1,574
Hemel hempstead
www.seatcupra.net
20250410_185436.jpg
Little mock up of the swirl pot. An8 outlet at the bottom. The two an2 on the side are the feeds from the 2 low pressure pumps in the tank. The fitting in the top in the return from the engine with a 1 way valve. A tee so it can go back in to the swirl pot. If not it over flows back to the tank...... hopefully
 
  • Like
Reactions: nd-photo.nl

Manic172

https://m.facebook.com/ManicMotorsport1
Dec 4, 2018
1,446
1,574
Hemel hempstead
www.seatcupra.net
Morning all. Right bits of progress finally welding the steering coloum. And lengthened the coloum.
IMG-20250422-WA0001.jpeg

Just need to do a bend or 2 just to help angle it down towards me.
Next fuel cell is now hopefully plumed in and electrics done. The rest of the fuel set up (incar not engine yet) it now laied out and bolted down into nutserts. I just need to start making fuel lines. That's a job for tonight
20250422_201420.jpg

But it's all slowly getting there now. Still loads and loads todo but can also see progress. Hopefully get me meet some of you lot at super touring power in June.
More updates soon
 

Attachments

  • IMG-20250422-WA0005.jpeg
    IMG-20250422-WA0005.jpeg
    597.8 KB · Views: 2
Adrian Flux insurance services - discount for forum members.