-
Hey Guest one of our sponsors Progressive Parts is running Black Friday and Cyber Monday offers - more details here
what did you and your mk3 leon do today
- Thread starter seatleon2012
- Start date
Finally got round to fitting the bonnet lift kit I got for Christmas......
Sent from my SM-G950F using Tapatalk
Sent from my SM-G950F using Tapatalk
Easy?Finally got round to fitting the bonnet lift kit I got for Christmas......
Sent from my SM-G950F using Tapatalk
Thanks!!!
Enviado desde mi SNE-LX1 mediante Tapatalk
Fixed an annoying rattle I've had for about 2 months. I've checked everything on the suspension, interior trim, seatbelts, seat locking mechanism. Turned out to be the boot latch, bit of tape and it's all good.
Today I tried to fit the 18x10 with et35 225/40/18 
Sits nicely..Today I tried to fit the 18x10 with et35 225/40/18
Poslano z mojega EML-L29 z uporabo Tapatalk
Only slightly push down into the foam when fully closed.
Sent from my SM-G950F using Tapatalk
Gave it a wash.
The Turtle Wax Hybrid ceramic products I used at the beginning of September have just about stopped beading.
Over 6 months protection, not bad considering we've had lots of rain and filthy roads around here, then 6 weeks where there was salt on the roads and decent amounts of snow.
The Turtle Wax Hybrid ceramic products I used at the beginning of September have just about stopped beading.
Over 6 months protection, not bad considering we've had lots of rain and filthy roads around here, then 6 weeks where there was salt on the roads and decent amounts of snow.
Fitted shiny summer setup. Looks nice next to painted calipers.
Just brake discs could be bigger))
Poslano z mojega EML-L29 z uporabo Tapatalk
Just brake discs could be bigger
))
Poslano z mojega EML-L29 z uporabo Tapatalk
Well done! Where did you connect the cables to?
Sorry, just seen your other post Re the fitting.
Added the bonnet struts to mine today! 10 mins to fit and look decent in my opinion. Much easier to use!
Left the manual lifter in mine thought. Just in case
Left the manual lifter in mine thought. Just in case
Cheeky haldex service @ 15000 miles.
Safe to say it needed it, the filter was quite clogged.
Unfortunately I broke the pump connector trying to get it off. Although trying to find a replacement proved difficult as the vw part number isn’t stamped on it. Managed to find it eventually so just in case it’s 1J0 973 722.
Parts required
Fill bolt (N90281802)
Drain bolt (N91082701)
Seal Kit (0CQ598305)
Haldex Oil (G060175A2) 850ml I used about 650ml
Pump connector (1J0973722) only if you choose to remove the pump.
Pump housing bolts torque to 9.5nm
Drain bolt 30nm
Fill bolt 15nm
All in all took around 2hours to complete.
Sent from my iPhone using Tapatalk
Safe to say it needed it, the filter was quite clogged.
Unfortunately I broke the pump connector trying to get it off. Although trying to find a replacement proved difficult as the vw part number isn’t stamped on it. Managed to find it eventually so just in case it’s 1J0 973 722.
Parts required
Fill bolt (N90281802)
Drain bolt (N91082701)
Seal Kit (0CQ598305)
Haldex Oil (G060175A2) 850ml I used about 650ml
Pump connector (1J0973722) only if you choose to remove the pump.
Pump housing bolts torque to 9.5nm
Drain bolt 30nm
Fill bolt 15nm
All in all took around 2hours to complete.
Sent from my iPhone using Tapatalk
Put a Maxton lip on her. Was a fun install, the first "big" thing I've done on a car since covid started.
Next up: sideskirts. And still in doubt about removing the center exhaust muffler...
Next up: sideskirts. And still in doubt about removing the center exhaust muffler...
Similar threads
