-
Welcome to our new sponsor Lecatona, a brand dedicated to enhancing performance for VAG group sports cars, including SEAT, Audi, Volkswagen and Škoda. Specializing in High Pressure Fuel Pump (HPFP) upgrades.
-
The forums will be offline for maintenance on Friday 15th November at 10pm for up to an hour. Thank you for your patience.
as you can tell, looks loads better than the normal milltek oval one. I went to Milltek direct and they made the cat back up whilst i was there....
Very tidy indeed.
Unfortunately I doubt I'd be able to get that tip over here in Northern Ireland if you had to get it specially made up.
I had the remap last december just after i got the car, and the milltek on Tuesday just gone
dancupra
Guest
And my next job is to fit this
I got one just like this on my car
it makes alot of difference imho enjoy it dancupra
Guest
I had the remap last december just after i got the car, and the milltek on Tuesday just gone
Wait till you get the down pipe and race cat on there matey..... its like getting the car re mapped all over again.... throttle responce and pick up is so quick
the oe stuff is so restrictive....On a seperate note, i turned my boost settings up yesterday and it was an animal
I had the remap last december just after i got the car, and the milltek on Tuesday just gone
Didn't get chance to hear the Milltek yesterday mate. Good meet though - now back to topic.
Fitted my Forge TIP today and what a pig of a job. Had to take the rubber top part off the oe tip to be able to turn the the metal part into the bulkhead so that it would pass a hard water pipe just to remove it ![[:@]](/forums/styles/seatcupra/oldforumsmileys/furious.gif "Furious [:@]")
Then I had to cut off about 2" of the Forge TIP so it would pass the same water pipe. All in all it was a VERY tight fit.
Results: Wall the turbo spool is so loud now and the dv sounds louder and seams a little smoother. Although I have only drove it about 2 miles so must do some more testing 
Forge TIP
OE setup
Forge TIP fitted
And this is how much I had to cut off
Then I had to cut off about 2" of the Forge TIP so it would pass the same water pipe. All in all it was a VERY tight fit.
Results: Wall the turbo spool is so loud now and the dv sounds louder
and seams a little smoother. Although I have only drove it about 2 miles so must do some more testing Forge TIP
OE setup
Forge TIP fitted
And this is how much I had to cut off
I'd like louder turbo spool. Shame it's only a petrol thing.
Nifty little mod though - my FORGE FMIC was a pain in the arse too...
Nifty little mod though - my FORGE FMIC was a pain in the arse too...
I'd like louder turbo spool. Shame it's only a petrol thing.
Can you not get a Forge TIP for the derv? If so yours would be even louder as derv's run higher boost.
Not that I know of....dervs dont have a dump valve so that'd need blanking - unless they make a seperate TIP....
dancupra
Guest
i got mine fitted when i was away on holiday at my porsche speacialists...... they did that, fitted new oe pads on the front, another bargain at £44+vat and a 10k service for £80
AFAIK they didnt have to cut anything off it though......
As for loud derv spool up...... full milltek system and a hybrid turbo and it will spool really loud thats from someone who knew
and a 10k service for £80 AFAIK they didnt have to cut anything off it though......
As for loud derv spool up...... full milltek system and a hybrid turbo and it will spool really loud
thats from someone who knew
As for loud derv spool up...... full milltek system and a hybrid turbo and it will spool really loud
I have a full custom made exhaust, decat with small backbox only, it is quite loud turbo atm but you can never get too loud really.
It's a lot louder than my parents 08 plate FR.
I have a full custom made exhaust, decat with small backbox only, it is quite loud turbo atm but you can never get too loud really.
If I do go for the Milltek it'll be the non-resonated as I'd like to keep it as quite as poss. Might even go custom exhaust tho.
Similar threads
