flashbsd
Guest
yep looked fine, 89%, just changed it for a new one, and started getting over 200bhp as you shoukd 
Jonzy
Guest
The way its been explained to me is that the load on the n75 should initially be high, then drop and then will come back up as the turbo runs outa puff
Mine usually goes 95% > 75% and then climbs back up slowly, someone correct me if im wrong.
Mine usually goes 95% > 75% and then climbs back up slowly, someone correct me if im wrong.
Correct, some tuners will initially jam the WG shut to aid spool up. High (95%+ duty) loads across the range indicate your requested boost is either too high for the turbo you have....or you've got a boost leak.
Dude, replace all of the crappy braided hoses, tighten all of your hose clips and stuff and then re-log. 4th gear is a much better gear to log by the way.
Can you remember what Boost/Timing settings were applied to your car when you had it mapped?
Can you remember what Boost/Timing settings were applied to your car when you had it mapped?
Jonzy
Guest
Just replace ALL vac hoses anyway, they will fail at some point guaranteed.
And also check the brake servo hoses by the green nipple that comes off the left side of the inlet manifold. Mine was split the other day and i was loosing about the same amount of boost as your seeing.
And also check the brake servo hoses by the green nipple that comes off the left side of the inlet manifold. Mine was split the other day and i was loosing about the same amount of boost as your seeing.
Right guys and gals, i have bypassed the N249 checked the engine bay for broken pipes. I "Think" i found one so replaced that as well.
Here are my logs from tonight, pretty much the same i think.
Here are my logs from tonight, pretty much the same i think.
Code:
Friday 19 May 2006 20:59:09
6K0 906 032 1.8L R4/20VT SEA 0002
Group A: '115
RPM Load Absolute Pres. Absolute Pres.
TIME
Marker STAMP /min % mbar mbar
17.88 1720 72.9 1110 1050
19.29 1880 91.7 1520 1240
20.78 2240 113.5 2080 1510
22.28 2680 132.3 2300 1780
23.78 3280 165.4 2380 2170
25.29 4000 167.7 2390 2250
26.78 4640 157.1 2320 2050
28.28 5120 147.4 2130 1910
29.78 5480 136.1 2040 1840
31.29 5800 129.3 1960 1750
32.77 6040 124.1 1890 1680
Group B: '118
RPM Temperature Load Absolute Pres.
TIME
STAMP /min °C % mbar
16.89 1680 33 0 990
18.38 1760 32 5.9 1130
19.78 1960 30 99.2 1340
21.29 2360 30 99.2 1590
22.78 2880 30 99.2 1890
24.28 3520 33 88.6 2240
25.78 4200 36 99.2 2210
27.29 4800 41 99.2 2000
28.79 5240 46 99.2 1870
30.29 5600 50 99.2 1800
31.78 5880 54 99.2 1740
Group C: '003
RPM Mass Flow Load Ign. Timing
TIME
STAMP /min g/s % °BTDC
21.78 2480 62.31 100 10.5
23.29 3080 95.47 100 6.8
24.78 3760 118.97 100 6
26.28 4440 135.25 100 7.5
27.78 4960 140.67 100 7.5
29.27 5360 143.56 100 7.5
30.77 5680 141.11 100 9
32.29 5960 143.11 100 9TimD said:
seeing your log i don't think you've got a boost leak and i agree with this part of martyn post :
Martyn said:
if you still have the k03 i would say the requested boost is really too high and that's why the n75 duty cycle is maxed out, for me it seems the ecu is trying to achieved a boost that can't be done by a k03.
is this stage 1 or stage 2 ?
do you have a sps3 or do you know which settings you have, the requested seems really high to me, i have found an old log from mine in hb8 and it was like that :
Code:
/min % mbar mbar
2480 121,8 2140 1610
2840 150,4 2270 1980
3280 178,9 2380 2340
3680 175,9 2390 2360
4080 166,2 2380 2250
4480 163,2 2250 2150
4800 155,6 2140 2020
5120 148,9 2050 1910
5360 139,8 1980 1860
5600 133,1 1910 1810
5800 129,3 1880 1770
6000 124,8 1830 1730
6160 121,8 1790 1700
6360 119,5 1720 1680
I thought it was requesting too much for a k03 2320 @ 4,640 rpm
The k04 on my LCR just about manages that!
The k04 on my LCR just about manages that!
Tim, get you local Revo dealer to check what setting it's on and then knock it down a notch or maybe 2. Running the turbo with 99% WG duty means that the its is working flat out, running a turbo flat out isnt exactly a good idea if you want it to last.
Similar threads
