results

Hey folks, in my quest to see if the clutch is slipping / car slower than normal, I thought i'd get a friend to log Block 002, Block 115 and Block 118 to see if I had missed the obvious...The MAF, but as Vag-Com showed no errors, I remember on my last Cupra, the MAF sensor went but never showed...

I think it's time to post a few pictures of my babycar, so here's what I've done thus far: Debadged the back Painted the boot "S" in black Changed the aerial from standard into small Calearo Shark Installed M3-Style black rearview mirrors Installed plain (no "S") front central grille...

Went down to TSR Performance today to get the car remapped. Heard some worrying stories about them in the past but my experience was good. Nice bunch of lads and they seemed to know their stuff. Just wanted to ask your opinions regarding the dyno plot they produced. The power...

Here's the printout for my K03S Ibiza at the RR day at AMD today. Mods as follows......... K03S with 4bar fpr Forge FMIC 3" Z-Ex Downpipe/100cel cat into 2.5" Scorpion exhaust CAI kit Jabbasport remap + boost controller Forge DV007P Forge TIP EVOshield inlet manifold gasket N249...

Hi all. my car has been misfiring recently even on idle so i changed the offending coilpack for a new one and now it idles fine but goes onto 3 cylinders when you put your foot down? any ideas? has got new plugs in also...

Well it took Mr.Hooch a good 5hrs to do what Mastertechs of Morden (name and shame the idiots) took over a week to do. The ko3s is now up and running:D Many many thanks to Hooch for doing the work and for not shouting at me for asking so many silly questions. Top top workmanship aswellmate, you...

Hi all, today i had my Seat Leon Cupra R tested on the dyno and the results are little disappointing. 212 pk and 390Nm with the turbo in limp mode it had 157 pk and 2**Nm so i guess the car is still stock or there is something not right ?? somebody tested his stock Leon also...

I posted the below in the TDI forum, but have been advised that I'd get a better response here... Didn't even know there was a VAGCOM section! Sorry if I've posted this in the wrong place... I'm terrible with forums and wouldn't post a new topic unless I really needed help! Could anyone...

had two runs on a rolling road here in northern ireland last night.both runs produced the same results. 250 bhp and 271 lbs/ft of torque.my mods are dynatwist induction kit with cai,custom remap,bailey dv30 recirculating dv,full miltek from downpipe back including high flow cat,4 bar fpr,thicker...

Hi, My engine light went on a week before last for 3 days, then went off, it then went a week and has now been on for 2 days ... managed to get her connected to a VAGCOM and got the following engine fault Engine #1 17704 - Error in mapped cooling system (usually temp sensor or thermostat)...

Hi guys/gals. I have an engine emmissions light fixed on atm. Has been for a short while now. I havent noticed much differfence in perfomance. I've had the car since Feburary. Leon Mk1 TDI Cupra From the posts of the boards I got myself a VAG COM kit off ebay for £12 lol and here is...

Thought it was about time to start a thread on my past and present Ibiza's. Only 19, and on my third! Starting off with my first car, "hand-me-down" from mother dearest; Never really took any pictures of her until it came time to sell. 1.2 12v! Served me well, college and back everyday. Even...

Picked up my new FR TDI 3 weeks ago, moved from a 1.4tdi ibiza to an FR and there a big difference, very impressed and the dealer was quick to sort out my minor niggles with the car. All in all very pleased, (just gotta try and post some pictures up now) going to try and post some other...

With apr stage1, carbonio, forge dv (with spacer) & today having had turbo back miltek fiitted (3"dp with 2.75" cat back) my cupra got the following.... Was done at tsr in bridgewater. First couple of runs was only getting 275. Guy said it was too hot. After lowering the load...

After my bad run down in pompey back in the summer she was back on the rollers today. I wasnt very confident to be honest but it all turned out good. After some minor 'tweeking' I managed to pull 231bhp & 263lb/ft. Which IMO is pretty much spot on for a k03s revostg2 (from what i have read)...

As said in t'other thread went to the Detailing World Rolling Road day today Some tasty cars there and Paramount Performance is a very impressive place But here are the results i had Car on the rollers Spot the Monkeh ;) Printout No Torque reading as apparently the lead that...

Had my cupra remapped by star performance today, engine is standard with only 007p valve on, Bhp figure seems quite low but they advertise to give around 190bhp now on their website, torque figure seems very high tho? It pulls very nicely in every gear and feels damn quick, ive never driven...

Evening all, me and a fellow member on here (Punch IT!) recently went to get our cars tested to see the power were running, both similar cars, different spec engines, modified in different ways. My car is a late 210 version, runs a basic CC stage 1 re-map tuned by Storm Developments in...

Had it done in September 2007 and meant to post it in the diesel section but forgot! :doh: Here we go anyway - done on a dyno-dynamics rolling road at JKM in Portsmouth area. Very happy, its an Upsolute Remap i've had around 15 months with the PD 160 intake pipes and a K&N panel filter...

I had my first rolling road at Rapid Chariots in Kent with quite a few members from SCN. Quite mixed results on the rollers there (dyno lottery) but I would appreciate opinions anyway. Here are the results: