FMIC Pipework?? Wheres yours!

[kyle'87]

Made it myself used self sealing hose take offs 25mm for the dv and 8mm for the N75 abit fiddly but works had no problems with it so far.

http://www.merlinmotorsport.co.uk/index.php?cPath=2661

Thanks for the link neil, can;t wait to fit mine now

 

[ibiza 22]

if you use them universal intercoolerpipes where do you put the intercooler sensor

 

[cupra-neil]

if you use them universal intercoolerpipes where do you put the intercooler sensor

I used the map sensor tube from Forge,

http://www.forgemotorsport.co.uk/content.asp?inc=product&cat=190101&product=FMMAPT

 

[Bazzle]

I used the map sensor tube from Forge,

http://www.forgemotorsport.co.uk/content.asp?inc=product&cat=190101&product=FMMAPT

t,

Thats what i did,think it was summit like 25 quid, new silicone hoses held up no problem, by held i mean the car is no more, was gettin boost spikes up to 2 bar and it blew the seals. So back to the start. Turbos off and goin to send it away to get refurbed lol

 

[Reuvers]

mine

 

[MIkey kc]

thant looks mint mate

 

[h17och]

why dont you just get the beads rolled?

i used the ali pipe from them ebay kits. got it welded etc.

 

[h17och]

beads nots rolled in pics above. i also got a mapsensor adaptor welded on to them pipes. much tidier

 

[PhilW]

Hooch, that was made from some generic FMIC pipe kit on ebay then?

 

[h17och]

yea. the picture in the 1st post. or which ever post it is

 

[h17och]

universal kit

 

[SeanyK]

Sorry to hear that Bazzle Hope you get it sorted soon.

Neil> What size hosing did you use mate for that 90 degree bend (to the right hand side of the rocker cover?) And also the latter part of the brake servo pipe-manifold connection?

 

[cupra-neil]

Sorry to hear that Bazzle Hope you get it sorted soon.

Neil> What size hosing did you use mate for that 90 degree bend (to the right hand side of the rocker cover?) And also the latter part of the brake servo pipe-manifold connection?

63mm will fit, atm the hard pipes are 60mm but going to change to 63mm soon

 

[Bazzle]

Weldin looks alot tidier, tryint o find someone who will do it without blowin holes cuz the pipeworks pretty thin, Problem there is findin a good welder. Think iv got it sorted now though. Some Majour tidy set ups here though. been aot of help for ideas

 

[SeanyK]

Hi mate, sorry I meant these pipes (circled) this is my engine bay;

 

[jamieread]

I used a 13mm 90 degree for the brake servo.
The crank case breather is a 19mm 90 degree.

See phil's faq thread on hoses: http://www.seatcupra.net/forums/showpost.php?p=1358522&postcount=9

 

[cupra-neil]

I used a 13mm 90 degree for the brake servo.
The crank case breather is a 19mm 90 degree.

See phil's faq thread on hoses: http://www.seatcupra.net/forums/showpost.php?p=1358522&postcount=9

Same here, just take the pipes off and measure them thats what i did

 

[Bazzle]

Started to redo mine, Still not happy but its not fixed yet.

 

[kyle'87]

What intercooler you running bazzle?

 

[Bazzle]

What intercooler you running bazzle?

Unicooler from fleebay! was about £80 i think. and the pipeworks from fleebay too. The guts of the cars ebay or forums lol.