mounting

Where does anyone mount their sat-navs? I've got a garmin nuvi and find it a bit too far away on the windscreen and the wires/adaptor make it look really untidy. Is it possible to hard wire it in? What about mounting on the dash? Any pics? What is the tomtom pre-install like?

Anyone know where i can get a mounting plate for 2 gauges, to be mounted in the centre console.

Hi every1....... Please help!!! I need the bolts to join the gearbox to the engine but I cant find the part numbers anywhere & SEAT cant help either!! For Ibiza cupra - AYP engine & EWP gearbox code. I have ETOS but it only shows regarding the cupra r EDT gearbox. I ordered some...

thoughts? fits in there quite nicely.... am sure with a bit of filing it would go well in there...would also mean less cabling and shorter length cabling which could potentially be good for the power and sound

Right last night I picked up a set of LCR brembos. The main reason being to replace the ones on my new LCR as the one on the car are peelng and discoloured. Now the original plan was to swap the calipers over and sell the ones on the car right now, but... I've just been mocking up the...

Ok I know where to put the harness in the rear (c-pillar), I know where to point one of the lap belt mounting points down by the door. BUT Where should I best mount the mounting point at the side of the handbrake? Where would be best to drill? Or mount it?

Evening chaps. The missus has bought me a Tom Tom One for Xmas. Got a while before I can open it, but it got me thinking...... Seeing as the Altea windscreen is a long way from the driver, making it hard to reach, I was wondering where else it could be mounted (and easily removed) ? I've...

Hi all, I've just sheered off my 3rd engine mounting bolt within the last 10 months :wtf: :cry: it's getting to be a right pain in the a*s*. Last bolt I had fitted I had made up and was supposedly 1.5 times stronger than the original. Definately not knocked it on any speed humps, and OK...

The caliper mounts on the cupra hub, are they the same as anything else in the VAG family, golfs etc. E.g discs are the same as a g60 Ta :)

I want to fit an oil temp gauge (for obvious reasons), but not sure as to where to mount the gauge :confused: I don't want it in the 'a' piller with my boost gauge as i don't like the look of 2 gauges up there and also don't want it down in the centre console like the Cupra R's as this is...

I have had a little search but cant really find much, how have you guys gone about mounting your gauge's on your A piller? Have you had to do some cutting?

Hi all :wave: I have now sheared off 2 engine mounting bolts in the last 2 months:stick: , these being the ones into the gearbox. Have now had it replaced by an extra high tensile one made up especially for the job by a firm that supplies bolts etc. for rally cars, this one apparently being 1...

Hey there, Off on holiday in the Toledo in a couple of weeks. Bought a set of third party roofbars specifically for my model of car (Toledo - 00-04), however I cannot figure out how to fit them. Removing the little plastic covers on the roof reveals nothing more than 2 gaps in the black...

Hi guys i need some help in finding a twisted bracket like the one shown below to mount my twister case to the (doh cant remember the word!!) thingy where strut brace goes. ( it is 3.20 in the morn !!!!!) Anyhows any ideas where i can get one...

Since getting my racing seat (Corbeau Sprint Xl) for the Cordoba I've been toying on ways to mount it. The problem is the taylored seat mounts that are on the market for the 6K chassis, they mount the seat too far off the floor, and being the 6'4" 19st person that I am, my head would be...