leon

Tools needed, flat screwdriver, torx bit 20 phillips screwdriver, wire snips (sharp scissors) electrical tape. hacksaw. Parts needed, 16.5cm speakers, autoleads sak-3103 adaptors. 1st, put a flat bladed screwdriver in the slot at approx 7 o'clock, put a bit of card behind to protect door panel...

I realise this isn't the most difficult thing in the world to do. But with fitting charges from £30-£120 I decided to save some cash and give this a go myself. I chose the Nextbase 512GW for several reasons: I wanted the option to record speed It had to be removable so it didn't get stolen on...

After doing this to mine i have decided to write a simple guide for it, Please note I am not to be help responsible if you break your RNS310. This guide updates the firmware on the device it will not update the maps! This guide is only for the RNS310, Not the RNS315,RNS510,RNS810 or any of the...

Just thought I would post up the VCDS mods that I know work on the Facelift Leon with Virtual Cockpit. For reference - These were all proven on a Leon Cupra 300 sc - MY18 - Virtual Cockpit For reference - I use a genuine Rosstech Hex-CAN cable with the latest VCDS software. Display Drive...

Links to helpful bits of info on this and other sites Battery Types and what they mean https://forums.seatcupra.net/index.php?threads/battery-completely-dead.439948/#post-4737776 and how to code a new one http://forum.obdeleven.com/thread/2041/battery-replacement How to upgrade you boot struts...

The purpose of this manual is to show you how you can remove the central console and then remove the switches out of the unit to enable work to be carried out. I will update over time to show how i fitted a stop start memory module (I need to run a 12v power feed to the back so on hold for a...

I was in the process of fitting a new rear diffuser to the car and it became obvious that i would have to remove the bumper to do this. I took a few photos and the rest is wordy but hopefully it will help you if you have to take off yours. HEADS UP - to remove the rear bumper you have to...

Purpose of the Brake ducts is to direct airflow from the front of the car onto the Brake Disks so that if you are doing a lot of braking or track work it helps to keep the brakes at a better temp. I have just been told some of the smaller brake systems may have issues with fowling on the...

Hi Guys & Gals, Today I fitted a strut brace to my Leon. It was real easy to do and took around 15 - 20 minutes. You don't need major mechanical skills to do this, just some tools. The tools I used were: 13mm sockets, 3/8 ratchet, 1/4 inch ratchet, a 1/4 inch driver and a 13mm spanner. Torque...

Hi guys and gals, This is an updated guide for how to fit an oil catch can for your 1.4Tsi engine. This is fairly simple and virtually anyone can do this with minimal tools. If you're wondering whether to bother fitting a catch can, google will explain much better than me, but essentially it...

Hi guys and gals, Just another quick guide for anyone who's been thinking of fitting a polyurethane bush insert to the lower engine mount, also known as the dogbone mount. This mod is quick and easy to do, with minimal tools and skill needed. In total it took me around 15 minutes. What you will...

Hi guys & gals, Here is a how-to to remove your front bumper. This is an easy task and will take around 20 minutes to remove, usually a little less to refit. The tools you will need are: T40 & T25 Torx bits Flat bladed screwdriver To begin with, pop the bonnet. Above the central grill there is...

Hi guys & gals, Got a big one for you today. This guide will show you how you can retrofit fit front parking sensors and enable the Park Pilot function on your Leon. This will be a lengthy guide so be sure to give it a full read first to ensure you can complete the job. This requires some...

Hi guys & gals, A nice simple guide today on how to change your oil & filter at service time. I'll also show how to change the pollen filter. I won't be talking about the air filter as I have a custom one on my car so there's nothing for me to change/clean just yet. Another point to note is...

Hi guys & gals, With the winter months up ahead and the nights starting to draw in, I recently fitted an LED strip to properly light up the boot in the dark. As I work at odd times, I often find myself in the boot at dark hours! This is a simple mod to do and requires a small amount of...

CHECK THE UPDATE TAB ABOVE FOR GUIDE UPDATES Hi guys & gals Today I will show you how to dismantle and remove the upholstery/covers from the front seats should you need to replace a damage part. I will also show you how to fit heated pads if you are wanting to retrofit heated seating. The...

Hi guys & gals, Today I'm going to explain how you can fit heated fan jets to your Leon and how to wire them in. These came as part of the 'Winter Pack' but can be wired & coded in with relative ease. This is relatively simple to do, and doesn't require loads of tools. Here is a list of parts &...

Hi guys & gals, Another guide for you today for a convenience feature more than anything. This used to come standard, but then Seat changed it to only come with the 'Winter' pack. However, it can be retrofitted! So I will show you how to do this yourself. For this job you are going to need some...

Hi All! I obtained these a few months ago, and they've been a great use so far. Here's a link to all of the Seat Workshop manuals for the Leon Mk3 3dr/5dr. https://drive.google.com/drive/folders/1M4ofxxMgsFjE7hNWg6l4KuifelmdMUu0?usp=sharing Here's a link to all of the Seat Workshop manuals...

Copied from https://www.awesomegti.com/blog/haldex-servicing/?fbclid=IwAR30co49F4pf4vwZE3E9nxP6IKORYIMtsaQN9tkVxFPzGP9il350JtSK9I8 Haldex Servicing - Why and When? Posted by Al Brown @ Awesome on 14th Feb 2019 If you have a small VAG '4wd' car; Whether it's a TT Quattro, an S3, a Golf...