hard

Hey everyone, I'm still 17 and live in Spain, And I'm interested in getting a Seat Ibiza when I turn 18. But I don't know what color, I always said orange, but I just got back from the dealer just to look and there was one in black, and I found really nice as well. But I want your opinions...

Hi folks! Weird one this, it happened the same day the poly dogbone was changed for a standard one, but went away after a spirited drive. But now it's back... Quite often when coming to a stop 1st or 2nd gear becomes hard to move to neutral. with some force it will move or if i move forward...

I replaced mine with another motor factor version (voided) and the nylon casing seemed too big to fit into the console so I got the file out and took some plastic off until it would sit flush so I could hammer it in. Does anyone know if the plastic ones should fit into the console without...

bit ov help please not shore wat goes on my car it a ac 1.6 5door 1998 seat cordoba, had a front end smash still drive but need spares, does anyone no wat models fit, i hear polos fit! but wonderd if any of the audi front ends fit on easyly

I have owned some good performance cars in my time but as the title says why is my 06 TFSI so bloody hard :( It twangs about the road ,with scuttle shake sometimes and the ride is just poor :shrug:is this the norm . I had a 53leon cupra R and the ride was spot on what have the Pedro's done...

hi everyone im interested in gettign a speed camera detector for my leon FR was wondering if it is possible to hardwire it to the car? and hwo hard it may be? also which devices to people recomend? Thanks Calum

i drove a seat ibiza today an 06 plate and the steering was really light, axtually most cars with power steering ive drove have alot lighter steering that my seat leon. the fluid level is high, so i do not understand why mine is harder than most cars with power steering

I have a MK1 leon 1.6 16v looking at lowering it slightly. Is it hard to change the springs? Took a wheel off today and had a look. Didnt look to bad to take the unit out. I know i will have to take it to get aligned when ive done it tho.

Ok so last piece of puzzle needed to fit intercooler and then remap. So does anyone know what size and angles of hard pipe i would need to go from the charge pipe down to the intercooler and from intercooler to inlet manifold? Was gonna look at silicone but feel that if i do it and...

Was wandering if I could swap out the "hard" pipes that run all around the engine bay with silicone vacuum tubing? I.e. will it be ok to do this, it's not the sizing I have the problem with. The pipes in question are all those running to the black box behind the washer bottle, that run down the...

My current dial/speedo has no plastic cover for the glass part and i want to change dials, if i were to pick up a dial can i straight switch it over?

Hi, the car has had new front discs fitted by the previous owner but under hard braking the the steering wheel vibrates! I haven't checked the discs for run out yet but wondered if there is anything else I should be locking at? Mark

HELP?? Clutch pedel gone rally hard and cant get in to gear any ideas?

Hi, Has anyone hard wired a road angel into a Leon ?? I don't like the cable being on show and find the position of the cigarette lighter not the best for having something plugged in that sits on the dash. I don't want to start randomly pulling at bits of the dash and console etc as its...

has anyone had a missfire at idle but no loss of power on a pd130 engine, can feel is shake through the car :( and when u accelerate fast theres a rattle sort of from where the turbo sits sounds kinda like heat sheild but nothing obv after having a look and ideas ?:cry:

Hey guys can anybody tell me if the seat leon cupra r 225 bhp suspension being hard is normal, and also the clutch? appreciate thanx

On one of these freezing mornings, when running late for work i couldn't get into my car as the door was frozen shut. Being a stupid oaf i pulled the door handle as hard as i could and now it's not sitting flush any more. The handle itself sits a few millimetres further forward than normal and...

wanna swap my inlet manifold over for my new powder coated one how hard is it? an how long would it take?should i change the gaskets?:confused:

Guy's I have a burning smell which has happen about twice now when pushing the my LCR hard. Has annbody got any ideas? Running Revo Stage 1, Bailey DV, Green Cotton. Thanks for any help.

as said above just wondering how hard it is to move the A/C back abit to make way for fitting of my new fmic fmic is this one if it helps...