easy

will mk2 wheels fit a mk1? ie stud pattern the same???:D

......Remove the Catalic converter like on and off? is it a big job? or is it just a matter of undoing the sensor, unbolting the pipe at either end then just removing it? then reverse when fitting it back on?

As title suggests, How easy? Usual Fitting time if doing by yourself? Tools other bits required? Any guides available? Thanks in advance guys SMlFFY

tbh i'm not thinking about doing this myself but wondering how long / big a job this would be for main dealer? had my car repaired (bodywork) and bodyshop checked / adjusted tracking, alignment whatever it's called. steering wheel now sitting slightly left when driving straight. put it back...

All, I've got an 02 LC. A little while ago I had a 'fuel too rich' error come up from an EML warning. Suspected the MAF and replaced that yesterday, but the error still persists and the car feels lacking in power. I haven't cleared the error codes - should I need to, or should the car clear...

Hello everyone, I've been quoted £75.00 to have my back box replaced with a straight through pipe with a tip of my choice. Quite reasonable I think. My main question is.Does anybody regret having theirs done? Does the 'Darth Vader' noise get annoying at all? I think I like the sound from the...

Hi all, I have a leak on both sides of the steering rack from the rubber tie rod seals (not repairable by dealers). A new rack is about £500 from the stealers, but i found somwhere local that will re-furb for £165. Do you think i'll get away with a DIY removal and refitting job? I know...

Hey folks, In the next couple of months, my next planned mod is to sort the suspension out, on 17"s my car sits higher than a tractor, so I plan to get new suspension. I don't really think im going to go the coilover route, I don't need adjustable height and im not planning on going round...

I am looking to get rid of my single nomad pillar and getting a twin one to house my boost gauge and oil temp gauge Is it easy to fit an oil temp gauge (as in fit it myself)? mechanical I presume? also how long does it typically take for the oil gauge to reach the right temp?

Hey folks, had a search, plenty of discussions about starter motors, but no one mentioning if it's an easy or hard job to replace. Ages ago I noticed like a grinding type sound when I started the car up, to me it sounds like it's coming from UNDER the car (Cat/Downpipe area) but anyway, it...

Would someone kindly be able to tell me what this belt is? Also could anyone tell me the part number. As the title says it's a 20VT Mk4. Cheers! or http://img211.imageshack.us/img211/3027/belt.jpg :)

Could fitting an interior LEDs cause the emissions warning light to come on? Hi all, Just a thought - a couple of weeks back I fitted an LED in the centre interior light (in the middle of the two map lights). I fitted it, tested it and left it at that - without starting the engine. The...

Hi there, almost got everything I need to get the install underway (minus amp and box) and just got wondering, is it relatively easy/hard to install an amp (Don't really want to shell out more money for installation costs). Gonna be running OAWG Thanks

I recently bought a 2nd hand cd changer for my leon and knew it didnt come with the wire loom, so ordered the loom from my local Seat dealer at a cost of £21.14 (with VAT). Was really excited when I got the call this morning to say it had arrived, so picked it up, went home and set about...

Hi All, I have an X Reg Leon 1.8t Sport, I bought this car on the cheap as cambelt had snapped and killed the engine! Just ordered an audi A3 Engine for it as the engine is the same. (APP). Cant seem to find anythin about doin this online and Haynes dont do a bloody manual for the car! A-...

Just finished doing this and i took some pics along the way, its taken be about an hour and the araldite is still curing... Get your parts toeather, you will need.... 1. Oasis bottle 2. Cable Ties 3. Washing machine Waste pipe 4. Small Jubilee clip x2 5. Araldite (Epoxy Resin) Tools: 1...

hi guys im new on here i drive a 53 plate leon cupra and was just wondering is the setup of the k04 the same as the k03s??

Got the B&M short shifter copy from ebay, instructions said you need to remove the exhaust, heat shield and tray sealing the linkages from the outside. Everyone i asked did this but i couldnt be arsed fannying about under the car. With a little bit of skill i had it done in 1hr all from...

Tdi Ibiza 2005, how easy is it to get the headlights out as i really wanna dry them out completely as there is some condensation that will not dry out in the corner and its bugging me. Is it a one man job or am i likely to need help. any help apprectiated. just found the search facility...

hi guys, happy new year ive not been on for a while but i am slowly building my 8v to compete in sprints and a few rallys. ive just bought a front strut brace from omp but theres no fitting guide. how easy are they to fit as in the past ive been lazy and used preperation companys, b but...