OBD Modifications

[KoNG]

If i remember right there was change in instrumental cluster so the previous 2020 didn't have it. Hard to say if that could be some how done with firmware update on the cluster.

 

[witek_77]

@simoammi Thank you very much. I installed the steering wheel number 5FA419091EL (I have Leon Xcelence), I did the coding according to your instructions and everything works. Cost 100euro

 

[simoammi]

- Disconnect battery iff you want or keep igniton off.
- Release the airbag
- Disonnect the airbag
- Replace the TKL module
- Put airbag back
- Reconventie Battery iff you did so
- Drive

Hi Antera! thank you for your explanation, the original module has 3 cables and in the photo it replaces only one. Is it still OK? Is it left original for the two missing ones?

 

[simoammi]

Hello ! Is it possible with obd11 to have this menu for Esc and Tcs ?

Yes !
the coding is this:

control unit 03 brakes ,

long coding you move to the bytes, drawing 0101010101
you go to the bottom moving all the way to the right, count 6 going back to the left and you find an entry starting with A, mine was A2
Remove bit 01 and put in bit 02 - the entry becomes A4 .
Scroll to activate.
finished

 

[RoadXY]

If i remember right there was change in instrumental cluster so the previous 2020 didn't have it. Hard to say if that could be some how done with firmware update on the cluster.

Yes, I also have an 2020 model (Xcellence trim) imported from Poland and I also don't have those settings...
Looks like a age thing then?

 

[witek_77]

Yes !
the coding is this:

control unit 03 brakes ,

long coding you move to the bytes, drawing 0101010101
you go to the bottom moving all the way to the right, count 6 going back to the left and you find an entry starting with A, mine was A2
Remove bit 01 and put in bit 02 - the entry becomes A4 .
Scroll to activate.
finished

Thanks again.

P.S. I ordered a KLR module for myself that has outputs for all three plugs.

 

[simoammi]

Thanks again.

P.S. I ordered a KLR module for myself that has outputs for all three plugs.

I see you managed to encode, great!

I bought this, but it didn't work and I returned it... the seller told me it was right for my car...

Page Not Found - Aliexpress.com

The steering wheel worked normally but it told me to keep my hands on the wheel

 

[witek_77]

I see you managed to encode, great!

I bought this, but it didn't work and I returned it... the seller told me it was right for my car...

Page Not Found - Aliexpress.com

The steering wheel worked normally but it told me to keep my hands on the wheel

I took this exact one from the auction you provided. so the one from this auction with an output of 3 didn't work for you and you bought another one now or Is the one from the auction you are giving is correct ? someone wrote in the comments that it works with Seat Leon. It hasn't sent yet and I have a chance to cancel it.

 

[simoammi]

I took this exact one from the auction you provided. so the one from this auction with an output of 3 didn't work for you and you bought another one now or Is the one from the auction you are giving is correct ? someone wrote in the comments that it works with Seat Leon. It hasn't sent yet and I have a chance to cancel it.

the seller says it is correct for my car, but it didn't work. i fitted the capacitive steering wheel after purchase, it was from an ateca, so maybe the decoder is different

 

[witek_77]

the seller says it is correct for my car, but it didn't work. i fitted the capacitive steering wheel after purchase, it was from an ateca, so maybe the decoder is different

ok now I understand. I have the Excellence and I also bought the Excelence version, only with the TA button. In that case, I'll wait for the shipment and let you know if it works.

 

[Antera]

the seller says it is correct for my car, but it didn't work. i fitted the capacitive steering wheel after purchase, it was from an ateca, so maybe the decoder is different

Its the same steering wheel. No Difference. De module works perfect without any issue for a while now

This one i hace:

Aiduauto Klr Mqb_evo 2q0 Permanente Lane Assistentie Off-Hand Module - AliExpress 34

Smarter Shopping, Better Living! Aliexpress.com

nl.aliexpress.com

 

[xaralam]

Yes !
the coding is this:

control unit 03 brakes ,

long coding you move to the bytes, drawing 0101010101
you go to the bottom moving all the way to the right, count 6 going back to the left and you find an entry starting with A, mine was A2
Remove bit 01 and put in bit 02 - the entry becomes A4 .
Scroll to activate.
finished

thanks i will give it a try !

 

[xaralam]

Can anyone knows the coding for service the rear brake pads ? Thanks

 

[Antera]

Google is your friend. Is no coding is adaption in ABS. It is selfexplaning

 

[xaralam]

Google is your friend. Is no coding is adaption in ABS. It is selfexplaning

Ok do you know how to put it in service mod using obd11 ? Thanks

 

[Jurisko]

Ok do you know how to put it in service mod using obd11 ? Thanks

Unit 03 Brakes / Basic settings /Start lininig change mode.
After replacement brake pads " End lining change mode"

 

[Leon xLux st etsi]

Hi Everyone,

I have been having a play with OBDeleven with my car (FR First Edition) and have managed to code some things and thought Id share what I have found and create a thread where people can share there findings for us all.

I have managed to code:
Cupra Display
Lane Assist Point Of Intervention (Have yet to test, but should keep the car more central rather then let it almost drift out of lane before kicking in)
Lane Assist Set To Last Setting
Lane Assist Warnings Turned Off


I know a lot of people find lane assist is already to sensitive (its already set to lowest from factory), so I might have found a solution to this too. So you can turn it off and it will remember this setting each time the car is turned on etc, so now you can make it sensitive for the motorway and only turn it on when you want it.


Cupra Display:
Module 17 (Dashboard) -> Long Coding -> View Activation -> Set All 16 Views to active -> Write To Car

View attachment 21580

Lane Assist Point Of Intervention:
Module A5 (Driver Assistance) -> Long Coding -> Point Of Intervention -> Set To Early -> Write To Car

Lane Assist Warnings:
Module A5 (Driver Assistance) -> Long Coding -> Lane Assist Off Text -> Set To Disabled -> Write To Car

View attachment 21581

Lane Assist Settings:
Module A5 (Driver Assistance) -> Long Coding -> Configuration For Lane Departure Warning K15 -> Set To Last Setting -> Write To Car


Let me know what you guys find

I have tried cupra view but no luck, I have active view 7 and 8

Hi Everyone,

I have been having a play with OBDeleven with my car (FR First Edition) and have managed to code some things and thought Id share what I have found and create a thread where people can share there findings for us all.

I have managed to code:
Cupra Display
Lane Assist Point Of Intervention (Have yet to test, but should keep the car more central rather then let it almost drift out of lane before kicking in)
Lane Assist Set To Last Setting
Lane Assist Warnings Turned Off


I know a lot of people find lane assist is already to sensitive (its already set to lowest from factory), so I might have found a solution to this too. So you can turn it off and it will remember this setting each time the car is turned on etc, so now you can make it sensitive for the motorway and only turn it on when you want it.


Cupra Display:
Module 17 (Dashboard) -> Long Coding -> View Activation -> Set All 16 Views to active -> Write To Car

View attachment 21580

Lane Assist Point Of Intervention:
Module A5 (Driver Assistance) -> Long Coding -> Point Of Intervention -> Set To Early -> Write To Car

Lane Assist Warnings:
Module A5 (Driver Assistance) -> Long Coding -> Lane Assist Off Text -> Set To Disabled -> Write To Car

View attachment 21581

Lane Assist Settings:
Module A5 (Driver Assistance) -> Long Coding -> Configuration For Lane Departure Warning K15 -> Set To Last Setting -> Write To Car


Let me know what you guys find

I have tried cupra view with vcds activated view 7 and 8 but no change
Is there any security access code?

 

[witek_77]

I have tried cupra view but no luck, I have active view 7 and 8

I have tried cupra view with vcds activated view 7 and 8 but no change
Is there any security access codey

SFD unlock, open bonnet, parking mode and handbrake. You can activate all views. I dont remember wchich one is cupra. I think its 6 or 8

 

[Leon xLux st etsi]

SFD unlock, open bonnet, parking mode and handbrake. You can activate all views. I dont remember wchich one is cupra. I think its 6 or 8

I have managed to do lane assist, but no new view how to unlock SFD?

 

[witek_77]

I have managed to do lane assist, but no new view how to unlock SFD?

What interface do you have ? Only obd11 have with pro/ultimate plan, odis with geko or token, VCDS/vcp/VCtool with token.