show us your small screen washer bottle

[chris_200120vt]

looking at the photos would say no good they look too big

this is what mine looked like http://cgi.ebay.co.uk/VW-GOLF-GT-TD...CarParts_SM&hash=item3cb70472e0#ht_583wt_1139

 

[tarzan]

hmm those big ones look like a 5.5 liter bottleHow big is yours?

 

[tarzan]

And one more problem i live in Norway and they won`t ship it to Norway

 

[chris_200120vt]

hmm those big ones look like a 5.5 liter bottleHow big is yours?

not sure would of had a look for you but the car is at over at jakes getting the full respray done , car less for another 2 weeks dont think they are 5.5 litres they dont take that much water

here is the Part number 1J0 955 453

 

[tarzan]

Part number helps alotThanks mate

 

[tarzan]

Edit partnumber is 1J0 955 453N thats the 3.0l bottle without levelsensor.
L or K at last is for the 5.0l bottle.

 

[neron4o]

Hey mate what size is that fmic

 

[neron4o]

1.2L Washer bottle hidden in front bumper:

Intercooler pipework, all custom:

Hey mate,
Nice work with the fmic. What size is it and the piping too.Did you go thinner from the hot side,and bigger after the fmic ? Thanx

 

[Mark_vRS]

Is that the best way to go? or is it just worth doing the whole pipe work in a bigger size?

 

[Chambers_CUPRA]

Just see mine

 

[neron4o]

Is that the best way to go? or is it just worth doing the whole pipe work in a bigger size?

Alot of people saying doing that is better for the flowand no lag. I am running k03s now,but going for k04, so the recommendation is to make it 2'' from the hot side,and from the cooler to the throttle 2.25''. I think I ll go for 2.25'' fmic in/out. The other way is 2.25'' all around. The other question is- 550x230x65 or smaller fmic. I think Robbie C is a little smaller tnan that but looks enough So what is the size ?

 

[Chambers_CUPRA]

Alot of people saying doing that is better for the flowand no lag. I am running k03s now,but going for k04, so the recommendation is to make it 2'' from the hot side,and from the cooler to the throttle 2.25''. I think I ll go for 2.25'' fmic in/out. The other way is 2.25'' all around. The other question is- 550x230x65 or smaller fmic. I think Robbie C is a little smaller tnan that but looks enough So what is the size ?

I've just K04'd mine and I'm running 63mm pipe work all round and 600x300x76 cooler and a 5Bar fuel pump
And most people go round the rocker so none of the pipe work goes under the floor getting damaged by low suspension.
Should have much lag with K03/s anyway

Good luck with k04ing it its a right pia

 

[neron4o]

Thats a big ss fmic,I'll glad to know what figures you are seeing ) I think I ll go for 2.25" pipie work all around and I ll measure the bumper, to see how it would be with 550x230 x65.Also considering to go 3" exhaust with 2 magnaflows. I m starting your showthread now Killer rims!

 

[Chambers_CUPRA]

Thats a big ss fmic,I'll glad to know what figures you are seeing ) I think I ll go for 2.25" pipie work all around and I ll measure the bumper, to see how it would be with 550x230 x65.Also considering to go 3" exhaust with 2 magnaflows. I m starting your showthread now Killer rims!

Made 286.2bhp and 309.8lbft torque.
Thanks mate

 

[neron4o]

My washer bottle arrived today so got on with fitting it.
Zip ties are a temporary thing untill i get my charge pipe relocation done down the side then i will do a proper job of securing it somwhere down there...loads more room now thiough.

One more question mates, on the first picutre of the above post, there is a black box with two hoses,that washer bottle is zipped on it, is this a part form the SAI, because mine is removed,but not in a propre way I believe

 

[Tucker157]

No not part of the sai. It's the carbon canister for venting fuel vapour through... Not required in the slightest! Except some silly euro rules for car manufacturers!

Solinoid on top can be mapped out, or left plugged in and relocated!


Sent from my iPad Mini using Tapatalk HD

 

[cuprabaz]

Pretty sure i've got an S3 washer bottle.