-
Welcome to our new sponsor Lecatona, a brand dedicated to enhancing performance for VAG group sports cars, including SEAT, Audi, Volkswagen and Škoda. Specializing in High Pressure Fuel Pump (HPFP) upgrades.
-
The forums will be offline for maintenance on Friday 15th November at 10pm for up to an hour. Thank you for your patience.
Leon 1P Vag-Com Cable ** Canbus OBD Diagnostics**
- Thread starter Knight_Rider
- Start date
dieselpower
Guest
Hi,
Received my cable as recommended in this thread and tried to do some of the changes from DANGB's Vag-com tutorial.
I managed to get most of them done, except the opening of the boot from the key fob. No problem I thought, bit more research and I'll come back to that one.
When I've gone to start the car tonight I get an error on the MFD that 'day driving lights front left/right defective'
All lights indicators etc are working ok.
I thought I was being carefull, following the guides to the letter as i've never done this before but must have messed up. i did have a problem viewing the long code helper comments in module 09. After doing some research and adding a .lbl file to the Rosstech folder I can now see them and both DRL America and DRL scandinavia aren't ticked.
Can anyone help??? starting to worry now!!!
Fault codes listed are:
2 Faults Found:
02745 - Bulb for Daytime Running Light; Left
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01111100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 147
Mileage: 73725 km
Time Indication: 0
Freeze Frame:
ON
Voltage: 12.15 V
ON
ON
OFF
OFF
OFF
02746 - Bulb for Daytime Running Light; Right
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01111100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 147
Mileage: 73725 km
Time Indication: 0
Freeze Frame:
ON
Voltage: 12.15 V
ON
ON
OFF
OFF
OFF
thanks
Neil
Received my cable as recommended in this thread and tried to do some of the changes from DANGB's Vag-com tutorial.
I managed to get most of them done, except the opening of the boot from the key fob. No problem I thought, bit more research and I'll come back to that one.
When I've gone to start the car tonight I get an error on the MFD that 'day driving lights front left/right defective'
All lights indicators etc are working ok.
I thought I was being carefull, following the guides to the letter as i've never done this before but must have messed up. i did have a problem viewing the long code helper comments in module 09. After doing some research and adding a .lbl file to the Rosstech folder I can now see them and both DRL America and DRL scandinavia aren't ticked.
Can anyone help??? starting to worry now!!!
Fault codes listed are:
2 Faults Found:
02745 - Bulb for Daytime Running Light; Left
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01111100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 147
Mileage: 73725 km
Time Indication: 0
Freeze Frame:
ON
Voltage: 12.15 V
ON
ON
OFF
OFF
OFF
02746 - Bulb for Daytime Running Light; Right
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01111100
Fault Priority: 1
Fault Frequency: 1
Reset counter: 147
Mileage: 73725 km
Time Indication: 0
Freeze Frame:
ON
Voltage: 12.15 V
ON
ON
OFF
OFF
OFF
thanks
Neil
dieselpower
Guest
Hi Andrew,
Yeah thats what I thought but the two options for DRL's (Scandinavia and America) in module 09 are unticked.
Unless there is another setting relating to DRL's? Or maybe the long code helper comments on my VCDS (805) aren't correct.
Anybody in the Burnley or Huddersfield area that can help out for beer tokens before I hang my head in shame and trudge to Richard Alexander.
thanks
Neil
Car is a 58 Diesel FR if that makes any difference.
Yeah thats what I thought but the two options for DRL's (Scandinavia and America) in module 09 are unticked.
Unless there is another setting relating to DRL's? Or maybe the long code helper comments on my VCDS (805) aren't correct.
Anybody in the Burnley or Huddersfield area that can help out for beer tokens before I hang my head in shame and trudge to Richard Alexander.
thanks
Neil
Car is a 58 Diesel FR if that makes any difference.
dieselpower
Guest
Been doing that and coming up blank. Reversed changes I had made and still the same. Maybe I've missed something?
Think I need to connect with the latest version bescause I think some long code helper comments are wrong on mine.
The post that Ross27 made in this thread on page 10:
09 (Central Electronics)
Byte 01 Bit 5 Rear Lid Remote Opening
Byte 01 Bit 6 Rear Lid Remote Opening - Release
On mine it doesn't list these, they are blank?
cheers
neil
Think I need to connect with the latest version bescause I think some long code helper comments are wrong on mine.
The post that Ross27 made in this thread on page 10:
09 (Central Electronics)
Byte 01 Bit 5 Rear Lid Remote Opening
Byte 01 Bit 6 Rear Lid Remote Opening - Release
On mine it doesn't list these, they are blank?
cheers
neil
dieselpower
Guest
Cheers Andrew that would be a big help!!
The alarm chirp on mine was on byte 10 where it was on 6 on DanGb's guide. This worked ok so didn't think to much about it but i wonder if other things are different.
have you changed the struts aswell? I bought the 520nm's as recommended by Ross27 in this thread. If I was gonna balls anything up I thought it would be when I swopped them. Haven't even got that far yet!!
The alarm chirp on mine was on byte 10 where it was on 6 on DanGb's guide. This worked ok so didn't think to much about it but i wonder if other things are different.
have you changed the struts aswell? I bought the 520nm's as recommended by Ross27 in this thread. If I was gonna balls anything up I thought it would be when I swopped them. Haven't even got that far yet!!
Hi lads
Any one come across this
Ordered the cable on page 36 followed the install instrutions for 704. All went well ran a autoscan from start to finish even cleared the DTC's for the Interior sensor
Ran the VCDS 8124 that came on the disc and now when i scan it goes as far as the climtronic and reports
can not contiune unautorised cable
Or some thing like that anyone got any ideas have i wreccked the cable?
Oh btw the laptop is very old no wifi and the was no ethernet connect so it could not hit the net.
thanks
Any one come across this
Ordered the cable on page 36 followed the install instrutions for 704. All went well ran a autoscan from start to finish even cleared the DTC's for the Interior sensor
Ran the VCDS 8124 that came on the disc and now when i scan it goes as far as the climtronic and reports
can not contiune unautorised cable
Or some thing like that anyone got any ideas have i wreccked the cable?
Oh btw the laptop is very old no wifi and the was no ethernet connect so it could not hit the net.
thanks
BigSighZ400
Guest
you may need to get the cable attached to a pc that can go online. there are drivers for the cable
Wrong!
Do that and this cable gets shut off and made unuseable, as Ross Tech disable them when they go online.
Not sure what to suggest though as ive ever encountered that!
Just bought myself one of these!
I know there is a guide for changing settings etc but is there one for monitoring live data? I'm trying to find the cause of an intermittent fault I've suffered with for the past 18 months!
[edit] - Bah - if I'd have read the above a couple of hours earlier I'd have had that off you!
I know there is a guide for changing settings etc but is there one for monitoring live data? I'm trying to find the cause of an intermittent fault I've suffered with for the past 18 months!
[edit] - Bah - if I'd have read the above a couple of hours earlier I'd have had that off you!
No probs, the new one was cheap enough, it would have been good to get it quicker that's all!
Here's a copy of what I posted in a separate thread in the vag-com section:
When the above is happening at idle, you can stand next to the exhaust and hear spluttering and spitting. It also feels as if there is more force (ie, blowing harder) to the emissions than normal. As I said, it only does it now and again though!
Here's a copy of what I posted in a separate thread in the vag-com section:
When the above is happening at idle, you can stand next to the exhaust and hear spluttering and spitting. It also feels as if there is more force (ie, blowing harder) to the emissions than normal. As I said, it only does it now and again though!
This morning i reofmatted the laptop and threw on a fresh XP install.
Installed 704.1 which was downloaded from the ship with a bay site, first problem was it would not use the drivers from the file from the bay site these are usb to serila drivers and XP refused to use them for my cable from page 36.
So i installed 704 which came on the little cd that caome with the cable and at the end of the install it asked to install a USB drive so i let it.
Started 704 and i had to config it as usual and it would only detec the the cable selecting USB not comports nore could i change it in device manager to use a comport as someone else managed to do on this thread.
Anyway did a autoscan and it got half way and then this is the exact message i got.
Sorry ! this function requires a license interface
Installed 704.1 which was downloaded from the ship with a bay site, first problem was it would not use the drivers from the file from the bay site these are usb to serila drivers and XP refused to use them for my cable from page 36.
So i installed 704 which came on the little cd that caome with the cable and at the end of the install it asked to install a USB drive so i let it.
Started 704 and i had to config it as usual and it would only detec the the cable selecting USB not comports nore could i change it in device manager to use a comport as someone else managed to do on this thread.
Anyway did a autoscan and it got half way and then this is the exact message i got.
Sorry ! this function requires a license interface
Similar threads
