South Wales Cupras Chat

[PhilW]

Yeah gettin my smooth one done this time.

Got a few tricks up my sleeve over the next few weeks as well.

 

[Forbez]

Oooh I like magic shows!

 

[mr_D]

I've got the F version as a spare, and dunno whats on the car.

Yeah i was in the cupra, but it was on the roundabout at Tredegar House entrance, so i'm not suprised you didnt see me.

Damn. Im usually pretty good for spotting the cupra's. Lol. Plus i had my little man in the car who was dancing to my music and i was pi**ing myself laughing at him

 

[Taffyman]

first time

nice car mrd

 

[mr_D]

nice car mrd

Cheers mate. Much appreciated.

 

[jivejester]

ghetto ebay b&m rippoff has arrived

Thinkin of taking the shifter box out and mounting it in the car now, save my cables

 

[Forbez]

Eh? You confuse me young man!

Going to ask you to give me a hand with mine one day.

And I will imburse you for the backpay of Classics that are still outstanding.

 

[jivejester]

Rather than run the cables for the shifter between the heatsheild and exhaust tunnel bring them trhough the bulkhead and bolt the shifter box inside the car.

Yea, im sending the boys round unless you come armed with a trade box of classics lol


Oh and phil has offcially turned into a complete homosexual, ill let him post the pic........

 

[PhilW]

Hahahahaha.

http://i22.photobucket.com/albums/b307/etahgnimusnoc/SANY0128.jpg

Its from one of my favourite engine bays.

Ordered them just now.

 

[Forbez]

Very Gimp / Rock n Roll!

Fear not young chaps!

The Classic's will make an appearance, you can hold me to that!

 

[jivejester]

Very Gimp / Rock n Roll!

Fear not young chaps!

The Classic's will make an appearance, you can hold me to that!

Yea yea, lost count home many times weve heard that!

 

[gazcuprablk]

does any1 know where i can get some real narrow 12mm spanners? snap on dont have any and the manifold is puttin up a fight so its either cut the thread smaller or mod some spanners,

badger5 is goin to tweek the map 2 so i dont end up blowin it up would like it set up for about 330bhp would that be 2 much?

 

[Forbez]

Go to somewhere like poundstretcher, Big W, somewhere cheap like that, they'll have thinner spanners.
Infact i bought some from Asda's a while back which are quite thin, hope they are thin enough for you.

 

[gazcuprablk]

ok cheers m8 another question now can i fit the turbo mani dp and still use the standard ecu to get about for now as i will be fittin these bits later 2day and wont be able 2 get the vag com on it til monday.

 

[Forbez]

I think you'll be fine.

 

[PhilW]

Just take it easy.


Daz, where did you get your alignment done? Full geo setup etc..?

Started ripping the car apart on the weekend, not looking forward to finishing this one off.

 

[Daz_gibbo]

Nah Phil, wasn't a full geometry. Just had the fronts done as the steering wheel was out when travelling straight since I sorted the top mounts.

 

[Forbez]

Phil, if you go to mototec gimme a shout.

Jivey, in regards to your exhaust rubbers, how in hell did you fit them to the car? I looked on saturday, and the mounts on the body of the car look like they'd need to be replaced, is this right?

 

[PhilW]

Rubber mounts were an arse, we had to cut them down load to get them to fit.

Tom, you need the alignment done or you just want a nose about as its close to you?

 

[rogers]

right my cousin has just txt me he wants his audi a3 1.9 tdi sport remapped, wheres the best place to have it now as westec are gonna's?