readings

hey people i was just wondering if anybody could confirm how to work out the rough bhp readings from the maf. ive had a quick search and posted in another thread and the rough guide was g/s x 1.3 gave the rough bhp figure but that was on an LCR with a ko4. is it the same guide for a LC with a...

VagCom MAF readings from my car today... Just want to know if there are any problems here and if you can tell if its been mapped here. My cable keeps preventing me from running full software so these are the only logs i seem to be able to get. Wednesday 3 February 2010 18:24:45 1ML 906...

I have noticed the coolant temperature gauge has been going to 90c then falling to 60c and then back up again. The temperature will fall when I'm crusing at speed with low revs to 60c (motorway driving), then rise to 90c when stationary or driving around town (i.e. constantly accelarating /...

i couldnt have the moving test as i dont have a laptop, just an extended usb which does the runway to run diagnostics from my desktop, so these results are done in neutral so probably not a good way to test but anyways..... this was the readinga as it idled against the maf vs lamda

Latetly my oil temp. and at times the coolant temp. rise above the norm - oil by 10 degrees and water - the needle moves to 105 degrees at times but mostly stays on 90 or maybe rises slightly above that. After a Vag-COM test, my mechanic noticed the Lambda correcting % is at Max, ie 25% and...

I was wondering why there is a difference between the rr and liquid gauge power and torque outputs. for example the car was stage 1 mapped in june on a hot day, on the rr it came out with 208bhp and 242 lb/ft, the liquid gauge today says 197bhp and 222lb/ft. I have only done approx...

Picking up my new car on Thursday 3pm :D 2008 (57) yellow 1.9tdi, getting it lowered asap, cant wait! and my current car im PXing... 2005 (54) agean blue 1.6 xsi :)

Hi guys. Can anybody tell me the peak boost and airflow readings for a standard and a stage 1 remapped Leon 2.0tfsi Cupra (237bhp). Any Vag-com logs would be handy! Cheers.

The BHP output on the engine power is showing 245. is this at wheels or flywheel. this is on the race diagnostic air vent gauge. i would take it its flywheel power but anybody can confirm

Hey folks, After scratching our hands to bits installing an oil temp gauge sensor today for both myself and Pulsebass on here, both of us now have strange, clearly incorrect readings. The gauges are Proshift, and came with a 1/8npt sender, so I purchased a 1/8 to m10x1converter...

Dont no if anyone else has this been my first winter with the cupra... couldnt find much on this when searched... i noticed recently when its cold outside like 10 degrees or below my engine temperature gauge will not go upto the 90 mark sits there fine when its warm outside not overheating...

Im not too sure wether this is the right section as my gt2x isnt really a ''Big'' turbo.. But here it goes... I done some logs last night and im getting stupidly high timing pull and Low Maf reading a 3'' tube?

Right guys have a slight problem. Not sure if it is something to worry about though. Ok, i just had 2 new tyres put on the front of my cupra R, and straight after i went and got tracking done by laser equipment. The garage showed me the reading and they are all over the place by the looks of...

Fitted my boost gauge today Teed it off the DV vac hose On idle, its sitting at about-0.8 bar, is this normal?? In gear, full throttle,it goes up to 1.5 bar and then starts to tail off to about 0.9 bar eventually does this sound right for a revod 1.8 20vT cupra? it doesnt seem to hold at...

does anyone sometimes get a low reading on the coolant temp guage? For the first couple of years ownership the temp guage used to sit on 90 all day long and never budge. Its there most of the time but sometimes it shows a low reading which seems wierd.. for example last night, I had...

hi guys, couldnt really find anything with the search. i had a p-torque remap recently and just fitted a boost gauge. what do you lot get in first? im only seeming to get about 11psi if i take it to the redline in 1st, but if i start off from low revs in 3rd / 4th / 5th and take it to the red...

Just finished fitting my boost gauge. When im cruising at most speeds it always reads bettween 10-20 Vac when i accelerate normaly it goes up to 0-5 then under hard acceleration its abtou 10-11. Is it normal to be on vac then crusing? Boost hose fitted to the top of the DV. Thanks Nick

my ibiza cupra is supposed to be mapped to 1.3bar by revo however my boost gauge only boosts to 6psi i have even tried another gauge as i thot this was faulty? car pulls like hell tho so it feels like it is mapped it throws you back any ideas ?

Ok just now fitted my boost gauge all seems to be working ok but just want to check what reading i should be getting? my car is a mapped 20VT. Any ideas please :help:

Hi, Does anyone know how to convert the Binary bits (bin. bits) taken off vag-com to mean something?? I measured block 030 on my LCR. Is it right from this I should be able to work out the Air/fuel Ratio of my car?? If this doesnt allow me too is there a way that i can?? Any help would...