Mine sailed through yesterday, emissions perfect with the Milltek TBE, cat in place. No issues whatsoever other than tyres being a tad on the thin side :whistle:
yayyyyy.....so happy
had 2 advisory's
1) brake pads wearing low (which i knew)
2) brake line on O/S has wear on (when it was dropping on it's arse by previous owner)
well chuffed :D
and all for £30 and i could help out my uncle with more cars too (as i know how to MOT minus the license to...
Right well basically passed my driving test on tuesday so have been out and about in the leon giving it a bit of a test only a 1.4 but insurance kills to have more. I know its not a stupidly quick car in a straight line but in my opinion it handles very well although I have noticed that when...
Hi,
My LCR passed MOT today so very happy but on the advisory it was not that my front tyres were close to legal limit. I have only had them 7 months and covered around 5000 miles is this normal expectancy for tyres?
I currently have Falken FK452's fitted.
Thanks
righto, seems to be a popular kind of thread :)
bearing in mind its not been driven properly since August 2008, and it's now april 2009 i'd like to you to take a guess at what (god forbid) it might fail on, i can rule out the following:
Wheel Bearings + Hubs - all replaced
Brakes - all...
anyone encountered this before ?
My Cupra is mapped with Revo stage 2
Basically it won't rev passed 3250 rpm, idles fine and will rev freely to that point no missfires nothing everything is fine untill then where it just won't rev any more and the revs bounce up and down like they would...
Hi guys,
MOT time this afternoon, 1st one for the LEON.
I haven't had to get one of these for about 4 years now - is there any pre MOT stuff I need to do ?
Only two things concerning me - 1 is that I have a slow puncture in one of the tyres (going to pump it up beforehand - but is this...
After nearly 2 years off the road, my little arosa went straight through its MOT this morning! Since buying it as a non-runner 9 months ago all i've needed is a temperature sensor to get it running, a battery as the old one had faded through lack of use, some clips to keep the window in, ht...
After owning the valver for six months it has passed the m.o.t. with flying colours, though I had to replace the:-
rear discs
rear pads
rear wheel bearings.
centre exhaust
rear exhaust
inner cv boot
top mounts
Cost a bit, but the car is now running sweet, glad it passed as the missus...
Just as it says,
I've been running this variable resistor in a box for around ten months and was going to remove it for MOT but did not have time . Thankfully it passed no worries and the box was never a smokey /ruff idle example. I am however gearing up for a remap when i can get the funds...
Put my GTi in for its mot thinking "well its 8 years old, will need a few things"
Phone call after 45 minutes of putting it in..
"mr McKellar, car passed no problem, not even one advisory" :D
Chuffed to bits, never expected that at all.
pointless - but happy post :happy:
Yes!!
As many of you know over the last few months I have been rebuilding a Cupra GTi 8v.
And last week it had its MOT and passed with flying colours.
And today it had its VIC check, passed that too. So now its all taxed. And ready for a drive.
xx
:D :D
I just wanted to share my good news with everyone after all the hassle i have been having recently, one good thing has come out of it!
YAYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY :clap: :dance:
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.