guide

This is a guide on how to get to the connector for the back screenwash located at the bonnet release at the passenger side for a SEAT Leon M3. I did this because my back windscreen wash was not going though. I could hear a noise when in use and noticed it was leaking from the bonnet release...

Welcome to my guide for replacing the rear pads on a 2017 Leon with an electric parking brake. The job itself is rather simple and straight forward, that being said you must be competent with working on the brake system of your car before you attempt this. DO NOT PROCEED IF YOU ARE NOT...

Hi guys & gals, Here is my guide for removing and refitting a new water pump/thermostat unit to the 1.4Tsi engine. My engine code is CZEA but this proceedure will be the same for other variants. Tools required: T25, T30 & T40 Torx bit & driver Allen/Hex 10 bit & driver Adjustable grips Flat...

SEAT Ateca Variable Boot Floor kit DIY installation guide applicable to Pre-Facelift (2016-2020) & Facelift (2020-present). This guide has been written to help people who have or are intending to purchase the variable boot floor kit that Seat Direct Parts have put together. Here’s the link...

IL Cattivo asked: "Hi guys, Last night I was trying to remove the headrest from the front passenger seat. [MKIII Leon FR 65 plate] Pressed the button on the side of the unit which allows it to slide up, but it then just stops and I can't get it to actually free itself from the seat, like I've...

hey guys and gals after having a slight debate over the way to do an n249 bypass this is how i would do it,i like to know your views on it.i see alot of people only doing half a job.a random guy with a 1.8t leon agreed to let me do this.it had a cat back exhaust an a air filter.this took me 25...

This guide will be kept up-to-date as information about the model changes over time. Specifications may vary from country to country. Introduction The CUPRA Ateca was the first vehicle to be launched as a standalone CUPRA in 2018 and based on SEAT's first SUV the SEAT Ateca. This guide is...

Syphon submitted a new resource: CUPRA Formentor guide - Model specifications, performance, colours and other options for the CUPRA Formentor. Read more about this resource...

This guide will be kept up-to-date as information about the model changes over time. Introduction The CUPRA Formentor was the first "Pure CUPRA" model introduced by SEAT's spin off CUPRA brand in 2020. It is an SUV, but is also known as a CUV or Crossover Utility Vehicle, a model that sits...

“Front Assist not available” came up after I changed from 18” to 17” wheels and added a full sized spare but around the same time I hit a pheasant at about 15 mph with no damage seen. Adding a full sized spare which on an estate is way behind the rear axle will misalign the radar sensor; the car...

A guide to replacing the rear pads and discs (272 mm) on a Mk. 3 Leon with independent rear suspension: The only difficult bit about this job is removing the caliper carrier bolts. The factory tightening spec is 66 ft/lbs plus 90 degrees which is very tight indeed. If the fasteners are rusty...

Right I know when I did this Char asked for a guide so I thought it was about time I got my bum in gear and got it done! Tools/Parts needed : Sidelight bulbs x4 (I have a sport model that needs 4) Hands Tissue or toilet paper Cup of tea ;-) Car used : 10 Plate Ibiza 1.4 SC Sport Time...

Very easy mod to do. Almost needs no instruction. Difficulty - 1/5 Tools - Small blade screw driver Washer Jet...

This isn't that difficult, time consuming, took me maybe 3 hours to remove and replace as an amateur (tbh, took slightly longer but that's because I had extra time figuring it out) This is on a 5dr but I don't see the being much/any difference between the versions, perhaps the 3dr might have 1...

So a few days ago my boot latch started making some rather funky noises and then suddenly wouldn't lock the boot. The noise sounded exactly like this (not my video) So I ordered a new part from eBay with the part number 1P0827505A9B9 but always best to use the number from your old latch to make...

Getting started: It's your cars birthday. And what do cars love more than cake? That's right oil! So first let's assemble the tools you'll need. As well as a jack, axle stands and wheel chocks (or house bricks) you'll need: Something to catch the oil! Newspaper to avoid messing up your...

I realise this isn't the most difficult thing in the world to do. But with fitting charges from £30-£120 I decided to save some cash and give this a go myself. I chose the Nextbase 512GW for several reasons: I wanted the option to record speed It had to be removable so it didn't get stolen on...

After doing this to mine i have decided to write a simple guide for it, Please note I am not to be help responsible if you break your RNS310. This guide updates the firmware on the device it will not update the maps! This guide is only for the RNS310, Not the RNS315,RNS510,RNS810 or any of the...

Just thought I would post up the VCDS mods that I know work on the Facelift Leon with Virtual Cockpit. For reference - These were all proven on a Leon Cupra 300 sc - MY18 - Virtual Cockpit For reference - I use a genuine Rosstech Hex-CAN cable with the latest VCDS software. Display Drive...

The purpose of this manual is to show you how you can remove the central console and then remove the switches out of the unit to enable work to be carried out. I will update over time to show how i fitted a stop start memory module (I need to run a 12v power feed to the back so on hold for a...