bracket

I found this bracket laying at the bottom of the windscreen near to where the wiper connects to the car, just under the lip on the bonnet. I recently had the cam belt replaced along with the water pump during a service. I imagine it’s from that occasion and it was either replaced with new or...

Hi, I am trying to upgrade my current seats to a set of OMP reclining seats. However, it seems impossible to find any! Can anyone point me to any? Thanks Isaac

Hey all, I'm looking for some assistance from a helpful mk4 ibiza cupra/fr owner. For some very strange reason, I have a component missing from my car, of which part numbers don't seem to exist, and SEAT are unable to get me a replacement. I can't find it on ETKA either. In basic terms...

Hi All, could anyone suggest a place i can get a Stereo mounting bracket for a Seat Leon 2000 model, it has the original stereo in at the moment and i would like to install my current one from my old car. it's a standard size stereo but i require a mounting bezel to fit it in nice and...

hey guys, my rear ARB bracket is broken, on the near side, is this a part which is easily replaced? if so do you think i good bit of welding will surfice? any help would be great oh and merry chirstmas Matt :)

i have been to my local seat dealer for the bracket that goes round the radiator expansion bottle and supports the clutch cable on the abf engined toledos and they cant even find a picture nevermind a part number so i was wondering if anyone on here can help me out with a number also the...

I have searched for about an hour and can't find anything, so .... Had a slow speed bump in my Cupra and the plastic surround bracket thing on the headlight that fixes the headlight in place has broken on both sides, though the headlight is intact. Is this a whole headlight replacement job...

Just wanted to see what people were using to hold their air filters in place. I have the usual set up with a conical filter.

Hey folks, So I fitted my boost gauge, and voltmeter (might change that one at a later date to an oil temperature one) today... Wired up both gauges to the same wires heading to the headlight switch. Didn't bother with switched, just went straight for backlight + and - Apart from the...

Just to make those with side skirts aware of a problem i have come across with my K1 but it could affect any car fitted with skirts. It seems the rear bracket that holds the side skirt on located in the rear wheel arch can be a bit brittle. Mine has snapped clean in 2 between the 2 screws. I am...

came from a 95 16v

Howdy Took my 1.8t Cupra in for its MOT yesterday and as you might have guessed by the title it failed. The only reason for this is some cheap crappy bracket towards the back of the exhaust has fallen off. My mechanic and mot tester is a close friend of mine and showed me where the bracket...

Ok so car went in for MOT yesterday & failed! grr! Only thing was the centre rear exhaust bracket broke, so figured this cant be to bad, phoned my local skoda garage to do the work gave my VIN number and they quoted me £205 + VAT for bracket replacement, i was like WHAT, she told me its...

Basically following on from my previouse thread of making a diy short shifter for the mk4 ibiza (I cant finde my previouse thread though but it was similare to this thrad). I'm trying to remove the gear shift bracket off the top of the gearbox but it wonte come off for love nor money. It has...

Went to change the rear discs today and found this... I'm sure there used to be two brackets here. Not the best idea to use aluminium brackets to hold all the twist of the ARB is it? They've never sat right, both have always been the same, angled into the centre of the car...

Hi, Put in the dynatwist on Saturday, but havent yet put in the supporting bracket as I couldn't find anywhere suitable to connect it to. There is a bolt hole by the passenger wheel arch, but it looks a too tight fit. Any ideas? what have other people done? it seems to be ok without the...

I just had the car back from a service and MOT (non dealer service). All went fine except i was told two of my exhaust brackets were broken to the exhaust was hanging on with only bolts. Apparently you can't buy the brackets and the only option is a new exhaust (c. £300 which is a sickener)...

Ello All, I've just had my gearbox reconditioned and installed in a 2003 LCR. I foolishly didn't look under the bonnet before I took the car away as I was in a rush and had a long drive ahead. Short of the long. The hose that connects to the steering rack seems to be hanging around and...

Right last night I picked up a set of LCR brembos. The main reason being to replace the ones on my new LCR as the one on the car are peelng and discoloured. Now the original plan was to swap the calipers over and sell the ones on the car right now, but... I've just been mocking up the...

hi guys i have just bought a kenwood 6 disc multi changer to fit in the boot of my mark 3 ibiza. the brackets supplied do not fit the pre drilled holes. any ideas? would it be worth buying a bracket from the main dealer? and if so would it be compatible with the changer that i have bought? thanks