block

Hi, I have a 2005 Seat Altea 1.9TDI. (VCDS version 908.1. genuine HEX-CAN cable ) I've lost some power of late, and think its a possible MAF issue. There are no fault codes, and MPG seems fine. Car feels slow to pull, just no oomph. This is my first time logging so have logged groups...

Hi again, Just tried to put a standard ISO SD/USB radio in my Mk5 Ibiza and found that the wiring block in the car wont fit a standard ISO radio ! I've taken pictures to show: Does this mean i'd need an adaptor of some sort to fit onto this and terminate into ISO connectors...

Rev-linked engine bay WHINING, goes away on the throttle, comes back off the throttle Hi, I have a 2002 Seat Leon with 120k on the clock. Things generally fine until last night when I do a bit of reversing, then switch back to forward gears. Since then there is a high-pitched WHINE which...

i've had to replace the window regulator and noticed that when the window dropped inside the door it landed on / hit a large square piece of black polystyrene. during the impact hit has split it and deformed it a little and more it from its original location. i thought i'd moved it back to...

Hey All, I did some quick logs today, 4th gear runs, everything looks ok but block 020 has me confused, Can someone look at the below log for me and tell me if the cyclinder timing is to much and what is normal, please bear in mind my ECU is remapped. Thanks in advance. Group A: '118...

Hey folks, in my quest to see if the clutch is slipping / car slower than normal, I thought i'd get a friend to log Block 002, Block 115 and Block 118 to see if I had missed the obvious...The MAF, but as Vag-Com showed no errors, I remember on my last Cupra, the MAF sensor went but never showed...

Hi, VAG-COM doesnt seam to fine a label file when im on the engine section of measuring blocks. For most other blocks it does fine a label file. Has anybody created a label file for this engine or know a label file which can work for it? Ill post this in the Leon Mk2 specific forum too...

Hey, as the title says. It would be easier to keep my car on the road while I built an engine in my garage, I was wondering if the N/A blocks were the same if I were to fit; * A new 2.0 FSi crank * 83mm forged pistons after a re bore * New rods Then when i swap the engine...

Hey, just removing stuff just now for BT e.g. o/s driveshaft. Had to remove this block What is it for? Only thing I can think of is to protect the o/s driveshaft maybe or steering rack? Any ideas? Cheers

Does anyone know if a APX head from a tt/s3 will fit a AUM (golf) or AQX (ibiza) 1.8t block? Thanks Tim

Hi all,I have just done a run with vag-com on my skoda octavia VRS and am trying to find a hesitation problem what are your views please. p.s i have also done block 002 and 115 if anyones interested.

anyone know where i can get one and the bolts and a resistor other than here https://www.ardesign.info/catalog/index.php/cPath/21?osCsid=fa4ac6b4efa95b2d3386e64f70a1c919

Recently I found out that my Cupra had a cracked engine block. With 52K on the clock and just outside of the warranty I am some what miffed :mad:. The fault started with a warning light coming on the temperature gauge; first of all it appeared to be a sensor fault but within a very short...

before getting my car remapped i logged a run with vag com on block 20 - measuring section. I logs the RPM and Torque in NM. Before mapping it read - 366nm @1911rpm Now After Mapping it reads - 380nm @ 2016rpm doesnt seem that much of a jump since it has been remapped and was...

..instead of routing through the bulkhead to the battery? I know there is an ICE forum but it's quiet as hell in there and I really need to know today. Red 12v connector Cheers Dom

Hi Guys, I should be getting my cupra in the next month or so, and was wondering basically what the cupras are like with milage over 65k? I've not seen many under that sort of milage, are they reliable still at 70k odd? Dont turbo's usually go around this point? Thanks, Andy

Vag-Com help Block 114/032 Do any vag-com boffin's know what the load values in block 114 should actually look like or does anyone have any logs of block 114 i can compare to? My cars Revo'd stage 2 and i've done various logs of block 114 tweaking the boost and timing. The corrected...

Dear Support, I am currently unable to access the Seatcupra site from my home ADSL connection. However from my NHS N3 link at work, all is normal. Could I enquire if your firewall is blocking my IP Address. This problem has occurred in the past and only happens when I had in excess of 20...

Hi, I am having some grief with my engine at the moment, and one of the possibilities is that the block (1.9 liter PD) is damaged (haircrack type scenario). I have a baffled sump for my PD130 (1.9) which I definitely want to keep. Has anyone here dropped a 2.0 block under a 1.9 head or...

Anyone else have one of these dangling behind the centre grill of the front bumper..... Is it used for diagnostics of the engine for mechanics.... If not where should it plug into lol... Thanks Ross