auq

  1. FR1.8t

    İs auq and bjx compatible?

    Hi i need to replace my auq engine from mk1 1.8t and i found bjx from ibiza fr is it compatible to auq engine is there any difference (anything, head, pistons, systems etc...) And is there any disadvantage (performance block, anything) cuz i didnt find a healthy auq engine but i found a healthy...
  2. Danycee

    3inch downpipe decatt fitting AUQ

    Hi guys looking for advice on fitting a 3inch downpipe/decatt to my 180 1.8t AUQ Seat cupra I have recently purchased one from Mpdevelopments they state it comes with the fittings to just sleeve straight on to the rest of the 2.5 oem exhaust and need some advice. 1. Can this be done on my...
  3. MLBrett

    Cold start issues

    Hi all, I've been having problems with my 1.8t AUQ engine. When cold, the engine will start, then stall and turn off, and will then start and run really rough until you pump the accelerator and it gets warm. When warm it'll start first try without a problem, however I can't be revving my car at...
  4. Mozboosted

    What stage am I at?

    I'm a newbie to this forum and vag ownership. I recently bought a cupra 2002 with auq engine. Im looking to add some mods as it does have a few already fitted but I'm unsure of what's next. I have forged rods (rated to 600hp) The N249 and n75 bypass/removal. R8 injectors R8 coil packs 3"...
  5. Help needed. 17743/P1335 - Engine Torque Monitor 2: Control Limit Exceeded

    Hi, I have a Leon Cupra 1.8t AUQ stage 2 (Badger5) I've been having the P1335 limp mode issue for a few months now. The first thing I did was buy a new Bosch MAF, didn't fix it. I then cleaned my air temperature sensor. Next, I replaced the MAP sensor for new Bosch one. I then unplugged my MAF...
  6. Ibiza FR 1.8t BJX Engine replacement

    Alright people, I recently acquired a cheap MK4/6L Ibiza FR 1.8t with a BJX lump in it. It’s showing signs of head gasket failure and doesn’t seem financially feasible to rebuild it. BJX lumps aren’t too common as far as I can see on selling sites, is it possible to do a straightforward swap...
  7. DubSteve68

    Suction Jet 06A-133-751 - Replace or Repair?

    Hi All, After 9 years of ownership the suction jet assembly on my 1.8T has finally sprung a leak and I'm getting the usual System Lean errors in VCDS as well as a nice hissing sound. So the question is obviously replace or repair? The best price I've seen for the full assembly online is about...
  8. Youshuddaboughtacuprar

    Newbie stage 1 leon owner

    Hello all, Decided to start a thread to follow my progress, gain ideas and answer possible queries. Will be uploading some pictures to show how she currently sits and what has been done so far along with future prospects. Stay tuned!
  9. logged runs on Vagcom, AUQ 2,032,115,120

    Hello i'm hoping someone could help me out with some vagcom logs. I have just got a Leon Cupra 1m, and have done some runs as although the car is fast higher up the rev range it doesn't feel so quick as the turbo starts up. It's a bit tricky for me to guage as i have only had the car a few...
  10. What 5 Speed Box For AUQ 1.8T 20V Engine

    Hi All, Any know what choices have I . I'm looking to put a AUQ 20V T into a MK2 Golf. I want to have it on a fluid clutch and use a modern box with it. I don't wnat the long ranges of an 02J 6 speed and would prefer a 5 speed, maybe something out of a VRS. Could anyone tell me the...
  11. Help Source Electronic Copy AUQ 1.8 20V T Manual

    Hi all, I am looking for help in sourcing a workshop manual for the following unit AUQ 1.8 20V T If it was something like a Haynes manual with multiple units , that would be perfect too. I thought that this would be the best spot to look for one Any help is very appreciated...
  12. Sparkie

    Torque on a standard LC with AUQ engine?

    Hey all, anyone know what the standard LC 180 bhp AUQ engine pushes out regarding torque levels? Cheers.
  13. CupraJ1

    AUQ engine & BAM engine

    Can anyone tell me if my AUQ block and head can be replaced with a BAM block and head. My engine is dying (oil pump), and I have the opportunity of a BAM. Obviously my inlet, turbo, exhaust etc will all be swapped over.. but Can this be done?? Thanks for help, James
  14. smivvy

    Turbo outlet pipe for 1.8T AUQ

    Ok, this is my last port of call to see if anyone can point me in the right direction. This is the pipe in between the Metal Turbo outlet and the so called 'pancake' pipe. Through many, many searches I have seen one by SFS that seems to be only for the Tdi engines. Is there an...
  15. superstar151082

    Auq engine

    I need to put a new engine in my 180 lc. The current engine code is auq. i'm finding it hard to find the auq engine for around 500 quid. Is there another engine code i can fit instead?
  16. Twin pass fmic? For leon cupra auq. . .

    ok, i understand that with the cupra its easier to get a twin pass fmic with inlets and outlets on the same side, however will this lack performance in comparison to an fmic with inlets and outlets either side?
  17. olliep

    lcr twintercooler on a AUQ

    i'm thinking of fitting the LCR twin intercoolers to my leon cupra. firstly, the off side intercooler, is it the same as the smic on the leon cupra as standard?? secondly, obviously i will need to get the inlet manifold with the TB on the right. Will this cause any other issues with things...
  18. forge 004 dumpvalve for AUQ 1.8t cupra

    ive looked through the threads but i cant find what im after. http://www.forgemotorsport.co.uk/content.asp?inc=product&cat=0006&product=FMDV004 , im looking at getting this DV as i herd it on a leon like mine on youtube but a mate said if i get this it will mess with the maf settings and send...
  19. bam engine parts on auq ?

    Hello there have a leon fr. am wondering can i put a cupra r inlet manifold on ? obviously i would need to change other parts but what would these be ? cheers my aim is to fit a new intercooler but i want a normal style cooler with the exit on either side .. cheers
  20. olliep

    whining down with revs (AUQ) (with video)

    Morning, For a month or so i've noticed a loud whining sound coming from my engine. It occurs when (for example but not limited to it...) out of gear, rev the engine to 4-5000 revs and let off. As the engine comes back to idle it makes a loud whirring sound starting loud and high pitched and...
Nimbus hosting - Based solely in the UK.